Cisco Pix515
Hi All, I cannot get opManager to discover / monitor our PIX515's I have the correct SNMP setup and the username / password configured for the pix? Can anyone help? Thanks in advance Leigh
How to monitor Cisco Pix failover with dedicatet LANFailover
I have the following problem... ..in Opmanger i can monitor two of four interfaces (inside,outside) on my primary Pix. The standby Pix has the same Interfaces (four) and i can monitor the inside and outside Interfaces. But now is coming the problem. Why can i not see the third Interface that is dedicated for Lan-Failover and the fourth Interface is administrative shutdown. I belive if SNMP is enabled on the Pix device all Interface are being discovered from Opmanger with SNMP Poll function. But i
Cisco mib and the right way to compile
Dear Support-Team, i am a newbie in SNMP but i read a lot of Cisco guides and now i have an running OpManager=>Cisco Pix and Router Monitoring-Environment. But the problem i have is that the traps from my devices are showing in OID form. I already did an upload from the Mib-Browser with all required Cisco-Mibs in the right compiling dependency. But is the upload equal to compiling? Must i do more steps for compiling and how can i get more text instead of OIDs in my traps I get to many OIDs from my
SNMP Configuration
I am new to OP Manager and have tried to configure it on all my servers. SNMP is enabled on all my servers but I do not receive my dials nor do I receive the sys Disc. What may I be doing incorrectly? Thank You, Gary
SMS Provider
Hi there, In the MSP version of OPManager is there a way to do SMS alerting via a web based provider ?. For example, www.bulksms.co.uk allow http submissionthat results in an SMS message. See: http://www.bulksms.co.uk/docs/eapi/submission/send_sms/ We use a small product called IPcheck from Paessler which supports this functionality, is it supported under OpManager ?. Any help appreciated, Regards, Steve
Cisco 3750 configuration
I have installed OpManager trial to see if it will fit our needs. I have discovered devices on the network and a lot of them seem ok, but my 3750 does not show any port information as other switches do. I have set a smtp public RO, is there anything else that I need to do? The 3750 is in a stack of two, is this a problem? Thanks in advance for your help. Sebastian
SNMP Question
I am new to this program and I have two ewbie questions. I have set up about 6 servers in Opmanage, they all have the same community string, but one server will not show the dials or pull SNMP data. I also have a server that is pulling SNMP data but i do not get a sys descr. but when i test the Monitors they are working. please help any advice would be helpful
Scheduled report question
I have a scheduled the All Server Disk Usage report to run every night at 2AM and have it sent to my inbox. I would like the report to be sorted by server name as it is when the report is ran from the reports tab. When it is scheduled, the report has no sort order and it makes it troublesome lookup the disk usage on a particular system. What will need to be done to have the scheduled report sort by server name?
SNMP
Hi there, I have bought and installed the latest version of OpsManager and we are experiencing problems with SNMP + the resource monitors. Basically, I am using net-snmp on linux hosts and opsmanager sometimes shows a dial for cpu/memory/disk usage and others times it doesn't. This happens completely randomly and makes fault finding rather difficult. One host might have all the dials working while another only has one dial working. I have ensured that the setup of net-snmp is correct by querying
Wake On LAN by Broadcast first?
Hello, I was wondering if it would be possible to change the order that OpUtils 4 performs the WOL (or at least make it an option). Currently when I select a PC to perform WOL, I believe it sends a directed WOL packet first, which does not wake our PCs up, but when it's status becomes "attempting to power upby Broadcast" the PC will power on. (FYI I believe the "upby" may be a typo instead of "up by", but that's what it says). So instead of having to wait 2 minutes before it sends a broadcast WOL
Event Log Rules
Is it possible to monitor additional events logs such as the DFS Replication log on windows? Can I add it to the default_event_rules.xml file? cheers
Clear a trouble Alarm!
Hi all, I am trying OpManager, and having a problem with the Alarms and Notification: I had set up Notifications for all my alarms, and i have one alarm from a Cisco Catalyst 4500 about some Ports that are down, they are "operationally down", how can i make OpManager ignore this error? I have tryed to unmanage that ports, doesn't solve the problem! Preferely i just want to say: "ok, i know, if something else change notify me!", becouse those ports may be used in th future and i do not like the idea
What do these failures mean?
Hello, I used to get these alarm messages: Trouble feb 06,2006 12:39:02 PM AuthenticationFailure : Trouble feb 06,2006 12:39:02 PM AuthenticationFailure : Trouble feb 06,2006 11:39:02 AM AuthenticationFailure : Trouble feb 06,2006 11:39:01 AM AuthenticationFailure : Trouble feb 06,2006 11:17:29 AM AuthenticationFailure : Trouble feb 06,2006 11:15:50 AM AuthenticationFailure : null When i restarted the SNMP-service on the source of this alarm these messages where solved, but now i keep getting these
Server Availability Report:: 7 servers shown as Down
Hello there My Opmanager is ok , except that on the Report section--> All server availability report, among the 40 servers I have, 7 servers are shown with 0 percent uptime for today. i tried for the "past one week report", result is the same. but on the "last one month" report these servers are shown as 60 percent uptime. for the last 2 weeks, these servers are shown as down by the report . and yet , physically all these servers are own and working properly with out giving any trouble. I went thru
OpManager stops collecting data
Hi, I have installed OpManager 6 from scratch. Windows 2000, SQL 2000 OpManager collected data for the 2 or 3 hours then it stopped. Checked nmserrx.txt file and find out and error that the data was truncated. I modified database_params.conf, wrapper.conf and SetEnv.bat in the way Rex told me some time ago as database connection was getting disconnected and to get through this it was necessary to move to MSSQL JDBC Driver instead of jtds driver. Checked new nmserrx.txt file and found a new error:
alert when monitor is unable to retreive data
Is it possible to create a notification profile that will send an alert whenever a monitor is unable to retreive data from a device ? I'm using a Telnet monitor to check available disk space on a Solaris server & I want to get a notification in case the monitor is unable to execute the telnet command (in case login fails or no response from the telnet deamon)
Update status and Alarms
Hi, I am testing opmanager in my network, and having a trouble: I have set the refresh interval of all devices to 1 minute and when a simulate a link down i do not get an alarm until i manually update the status of the device in the "update status" action. What's wrong? Isn't the update automatic? And one more thing: What is the "Last Polled AT" and "Next Poll At" in a device? Because i always have a few days back, like for example today i have in a device: Last Polled at Out 26,2006 06:15:56 PM
Switch Port Mapper shows availible when it's not
It will show available in green, sometimes it will show a mac address sometimes it won't. But the available port count is always off. Transient ports do it as well, in the screen shot I attached there is 4 Transient ports that show in red and 1 in green, Available show 10, 4 in red and 6 in green.
Failed to create shared memory
When trying to start the OpsUtils, I receive the error message ' Failed to create shared memory'. Any idea what I must do to be able to start the service?
Failed to establish connection with web server. Gracefully..
Hi, I've search all posts about that subject and still have problems. 1st i've the mysql stop at the start and made copy of lib and no more msg of mysql and i startmysql.sh and that is ok. 2nd the Verifying connection with web server ... Failed to establish connection with web server. Gracefully shutting down OpManager. I change the ChangeWebServerPort.sh 8080 9000 and the problem still the same... i change for 8080, 9001, etc etc and still the same problem... i look at the logs and stilll can't
Can Not Delete Device
When I try to delete any device in OPmanager on Red Hat Enterprise 4.0 it display message : Status message Your delete request is being processed.Please check after sometime. But the device not get deleted. What cab be the problem & how can I delete it?
Receiving traps from a AR410 router
Every 4 hours is receive the following alarm from a Allied Telesyn Ar410 router: .1.3.6.1.4.1.9.2.9.3.1.1.1.1: 5, tcpConnState: 7, .1.3.6.1.4.1.9.2.6.1.1.5.172.16.188.8.23.172.16.188.28.4053: 544, .1.3.6.1.4.1.9.2.6.1.1.1.172.16.188.8.23.172.16.188.28.4053: 152, .1.3.6.1.4.1.9.2.6.1.1.2.172.16.188.8.23.172.16.188.28.4053: 5498, .1.3. It contains the address of the server where opmanager is running (172.16.188.28) and the address of the AR410 device: 172.16.188.8 It seems that contacting the router
Opmanager 6 on Debian mysql error
Hello I figure this must be a known or common problem. Im installing the above on Debian and when I run the start script ./StartOpManagerServer.sh, I get this error inside addon check Unable to start Mysql daemon Unable to create database Exiting OpManager This is similar to the thread in http://forums.manageengine.com/forumHome.do?forumGroupId=49000000002007&forumTopicId=49000002639827 I followed the suggestions in it and the end result was to contact support, no follow ups seen on this. I removed
Partition Detail Resource Monitor query
Hi, One of the Resource Monitors, Partition Details provides the %used of each disk partition on a server. This is very useful to use as we like to keep 20% free on all disks and get an alarm raised when this threshold is broken. However the monitor also includes the same info for physical and virtual memory and we often have less than 20% physical memory available. Is it possible to 'turn off' the information for these two so that we do not get unwanted alarms. regards, Doug
Alarms history and reporting
I would like to have the ability to run reports on all alarms received on a daily, weekly and monthly basis. Currently I have the notification profiles to send an alert when a service is down, or a threshold is violated, etc. And another when the alert is cleared, but when I look at all the alarms, it just shows the last alerts received. For example: say I get an alert that CPU utilization is over 80 % at 10:15 am. At 10:30 am I get another one that CPU utilization is back to normal. When I look
Issue with notifications
Opmanager is not sending out notifications when an alert is triggered. I looked at the notifications log and I found why it isn't. "Could not connect to SMTP host: localhost" For some reason Opmanager is trying to use localhost to send out notifications even though it is configured to use our mail server as it's smtp host under Admin - Mail Server Settings. I went back and reconfigured the mail server setting but it is still trying to use localhost. Any ideas on how to fix this. Thanks
Servers not polling
I tried to search the forum for this issue but I couldn't find anything similiar to what I am experiencing. I have a few servers that I have added to monitor. They add properly and I can view them under the "maps" tab. But when I click on the server the dials do not appear and there is no polling data for the server. If I click edit for "cpu utilization" and then click test - the test passes and the dial shows up until the next poll interval. Once the next poll interval runs the dial disappears and
Debian Install a Nightmare
I have spent forever following the incorrect install manual for debian and trolling through your forums trying to get the damn trial working. So far i've ignored the suggestions to copy the libdb 3.2 file cause it's for redcrap not debian and i've linked the real debian libdb3 file in the /lib folder. Now that this product starts and i can log in it will not start up properly. I'm getting network connection failure and it's driving me crazy. Especially cause the box is cleanly on the network and
Traffic Reports low in detail
My Rx/Tx traffic reports are not as detailed as they were before. On a report generated for today, detail is high, on 7 day Report there is a change in detail from about 4 days ago which detail was high but since detail has been very low. Monitoring levels are set at 1 minute. An example is given below.
The display name is too far from icon
The display name is too far from icon, i have to separate objects more far, and the map will become more big. Can the display name near to icon?
OpManager MSP version question
My company has purchased MSP version and few probes. So far the product is great, however i did have questions about rebranding the client piece; 1) Is there a way I can totaly disable web/administration site on a client probe? That way i can have a customer just login directly to our main customer site and generate reports or other tasks. 2) Does the customer really has to download a 49MB file just to install a 5mb probe? 3) Can we rebrand the probe ? so it has our logos maybe our tech support numbers?
How Can I Monitor Disk Space Indivisually for all Hard Disk
How can I monitor disk space individually for all hard disk drives in OP manager on Red Hat Enterprise 4.0. At present it shows total of all hard disk drives.
SNMP Trap Processor severity question
Hi there, I'm evaluating Opmanager and have a question about Trap Processors. I've created one trap processor and it has mailed me these in the body of 3 emails: Message: Trap received from with SNMP Varbinds sysUpTime: 2 days, 1 hours, 20 minutes, 40 seconds. , .1.3.6.1.6.3.1.1.4.1.0: .1.3.6.1.4.1.7684.1.1.1, .1.3.6.1.4.1.7684.1.2.1: Call routing service is shutting down Message: Trap received from with SNMP Varbinds sysUpTime: 2 days, 1 hours, 21 minutes, 41 seconds. , .1.3.6.1.6.3.1.1.4.1.0: .1.3.6.1.4.1.7684.1.1.1,
Self Test to insure OpManager is functioning correctly
Hello, I'm trying to gather a list of items (processes, services, logs, etc) that I can monitor and have a reasonable "self test". The point behind the self test would be to determine the health or running state of the critical parts of the monitoring engine. The important parts being the scheduler, data collection, rule engine and alert system. The Self Tests will be completely separate and not rely on the OpManager since that would create a single point of failure. Any help identifying where to
AuthenticationFailure : null
Hallo, I am using OpManager 6.0, Build 6002 with Hotfix 6 on a Server with MS Windows Server 2003 SP1. This server monitors 3 other servers, 8 print-servers and 1 switch. Every 5 minutes i am getting from the montoring-server the following alarm: Trouble Mai 01,2006 10:42:37 AM AuthenticationFailure : null When I delete all monitored objects it stops getting this error. Has anybody had the same problem or know, what to do next? Thanks. Ciao Roland
Customize snapshot views?
Hi, I'd like to add different gauges and views to the main page of a device. For example, when clicking on a server, there are guages for CPU load, Memory load, etc. I'd also like to add Vender Specific monitors into the gauges, such as temperature, so that I can view easily without generating reports.
ServiceDesk & OpManager
Hi There We have Opmanager, Eventlog Analyzer and Service desk all running quite well on the same server, but using different DNS alias's so I can move them at a later date. ServiceDesk is running with Active Directory and gets all its users from there. I am trying to integrate ServiceDesk and OpManager but get the error "Unable to fetch values from ServiceDesk Plus, The server might not be running or the network traffic may be too high. " I have tried using my login details both ({domain\username}
XML file monitoring
I want to monitor attribute in XML file on remote web server This is the sample from http://10.1.14.11:8081/Software/Sitestat.xml <SiteStatus Status="Enabled" CatalogVersion="20061107044703" /> My company have more than 600 node of this monitoring required. Please recommend the software that can do this function. PS. the value in xml file is dynamically
Enable auto login
Hi, I trying opmanager and its great. We�re thinking on buying it to monitor our network but there�s a question we need answered: we already have a kind of a map, with all our servers and network elements. What I would like to known is if there�s a way to enable autologin in the web client, so I can direct the page to a given host ou server ou whatever. In short I would like to integrate in my company existent "network map" links to elements monitored by opmanager. Is this possible? How can I integrate
email notification when receiving snmp traps?
Hi, I'm configuring some snmp trap processors, but I cannot find where to specify to generate an email notification when a trap is received. This is not possible? Thanks in advance
Next Page