Guide for NetFlow Analyzer -> Not Updated.
Hi, I have tried the guide for the NetFlow to enable it on the IOS ver. 12.4, but it does not seem to work. I've checked the version of the Guide and it is for 12.1. I hope the guide can be updated soon, as this will be such a confussion for other users. The 12.4 release can be found with this link http://www.cisco.com/en/US/docs/ios/netflow/configuration/guide/cfg_nflow_data_expt_ps6350_TSD_Products_Configuration_Guide_Chapter.html#wp1057626 Thank you. Cheers, Andy
how to batch add notification profiles for devices
there are above 100 device in the opmanager database. Now I want to add notification profile for each device, and let me can receive mail reminder when device broken. But I can't batch add notification for devices. Any Guys can give me some suggestion? Thanks in advance
sycn users with AD
Is there any way to sync my users in OpManager with microsoft AD accounts?
net-snmp auto restart every 48 hours on a SUSE Linux 10
A Dell PowerEdge 2950 Server with SUSE Linux 10 installed. I configured snmpd service(net-snmp) to send trap to my OpManager.(trapsink 10.11.0.140 public) OpManager receives coldStart trap on every 48 hour at 9:30 am. Here is the time table. Apr 21,2009 09:29:54 AM Apr 19,2009 09:30:36 AM Apr 17,2009 09:30:07 AM Apr 15,2009 09:30:46 AM Apr 13,2009 09:30:23 AM Apr 11,2009 09:30:27 AM I check the server today, the server *DID NOT* rebooted at all. On that server we have JBoss4.0.3
Multiple SNMP credentials
Hi, We're monitoring several linux servers, and require a different snmp port for squid as opposed to the standard snmp monitoring port. We've tried setting both sets of credentials, but it seems from the snapshot that we can only apply one set (and one port) to the server. Rather than forwarding the ports on the server, is there a way we can use different snmp ports for different checks?
Email priority?
Is there a way to setup email priorities so that certain alerts/notifications have different priority levels when they are sent through email?
Setting up for the first time
Hi, I'm setting up OpManager here for the first time and seem to be getting some strange behaviour. 1. I have added 2 URL monitors and while they show up on the Infrastructure Snapshot, they do not appear under the URL monitors and so I can't edit/delete the ones I have already added 2. I have added 2 firewalls and again, they show up in the Infrastructure Snapshot, but they do not show under Firewalls - if I chage it to 'List View' in the firewalls section they do appear there. Am I just using this
Can't set thresholds---Edit missing/changed
Heya, I recently upgraded from v7.x to build 8006. In v7.x I was able to set thresholds via edit but that is now missing. Were there changes to this or perhaps a bug? Thanks.
Discovery crashes network
Hi All, We have a problem where by the discovery task keeps crashing our network. Lots of broadcasts. Has anyone else experienced this? ta
not polling device with snmp?
I have bunch of Cisco devices that aren't being polled via SNMP. They are discovered but then not updated for traffic, interface status, etc. Any ideas? I've tried to delete and then re-add them...
State buffer or stats data files age limit exceeded.
Hi. When I enter in my application I get an error but I've been removing and still appears not to do, send me the following message: State buffer stats data files or age limit exceeded. I can support someone to fix this because it is annoying. Thank you
Urgent : availability distribution issue
Hello, I migrated to OPManager 8 build 8006. after few days, avalaibility distribution is not working, I can see last 24 hours, yesterday but others are not working. e.g. when I select last 7 days, distribution shows some days but not the 2 last days. if I select last 24 hours or yesterdays, it shows the avalaibility it is urgent for us as management is using dashbords set for them. Regards Philippe
Shorcuts not working on Dasboard.
Hi, I created a couple of Business Views and when y add the top business view on the dashboard it doesn' t take me to the sub business views.
Bug in process monitor?
I've run into an issue where we are monitoring the number of a specific process on a Windows 2003 server. Initially we set it up to monitor for 100 instances of said process, but now need to monitor a higher count. Unfortunately, when you type anything higher than 100 in the "Instance Count" "Value" field, it comes back with an error that the number must be equal to or less than 100%. I'm guessing it's just a coding error and the field checking algorithm was mistakenly copied from the fields above,
rediscovery doesn't work for interfaces
Hello Gents, Interface descriptions were changed on the switch. I tried to rediscover interfaces. OpManager found changes, I applied 'add' button, but there were no changes. All descriptions are the same. I can delete an interface and add it again. But it deletes all statistics, that's not good. I see these troubles on 30 (!!!) cisco devices. Also I have troubles with Cisco 6500. I re-added this device. OpManager didn't recognize the box. I added a custom OID into template and it was discovered.
Adding MSSQL Server Monitor
When trying to add the monitor to multiple servers I receive the the following error. "80041010 - Specified class is invalid. Try running 'wmiadap /f'(For Windows XP and 2003) or 'winmgmt /resyncperf'(For Windows 2000) command from the monitored device. Refer Troubleshooting Tips" To which I have followed all of your advice with the exception of restarting the MSSQL Service as these are production servers. What are the requirments for the credentials that are used to access the wmi information on
Problem adding device
Hello I have a problem adding a device. I receive the error message: Entries for the device are either partially added or removed. I've searched this forum, but all the threads related to this topic don't work for my environment. I'm running OpManager 7202 on a Windows 2003 server and connect to a MS SQL server. Thanks for any help Rainer ------------------------------------------------------------------------ OpManager installation: Proliant DL 380 G3, Xeon 2.4 GHz, 4 GB RAM Windows 2003, 5.2.3790
Jump To
Is there a way for me not to go to the Jump To, to access the Service desk, the device Expert and the Netflow. When I am in Opmanager I have to select the Jump To and then access the other plugins, is there a way not to do that. Also when I do that it logs me out of Opmanager and then I have to re-log back in.
Error adding notes to an alarm
We are on build 8006 and we are now having issues adding notes to alarms. If a new alarm comes up and there are no existing notes, we can successfully add one new note. However, if we try to add a second note to any alarm, we receive the following error: "Unable to Add Note some error occurred". We have tried doing a db repair and restarting services. I tried searching the forums, but could not find anyone else reporting this error. Any ideas?
Upgrade to 5031 and failed my config manager
I update the OpUtils and now OpUtils not capture configs of my device CISCO. I have a great problem, it's my backup. The firebird database fail.
Response times and Alias Names in 5028
I have requested this back in April of this year but wanted to take another stab at it to see if you might consider doing the following : 1.) It would be helpful to allow the network monitor list to be sorted by alias name. 2.) When sorting by Response Time, the list is being sorted on an alphnumeric basis when it should be sorted on a numeric basis. 3.) If the system cannot report patial MS then there is no reason to have the response times shown as 4.0, 3.0, 2.0, etc. where the tenths field is
Bridge MIB
Is there anyway to tell if a switch supports the bridge MIB? I have WS-C4948-10GE configured, but the application isn't show any MAC addresses listed on any port. Thanks,
False Alarms
I'm encountering a problem where OpManager reports that ALL devices are down and sends alerts for all devices. This has been happening usually once a week, but I can confirm that no lines are down in the datacenter to cause a loss of connectivity to all sites. When I check the ping monitor, there are no lost packets during the time when they are reported as being down. Any suggestions?
Problem with IP SLA information
Problem with IP SLA information
CLI Login Issue
I have an Avaya Call Manager Server that is essentially running Red Hat Linux ES3 that I have a problem logging into for CLI monitors via SSH. The issue is that this device requires an extra step at login to set the terminal type that I cannot seem to encompass within OpManager. We are running Opmanager 8 with the most recent patch with a Windows 2003 Server, MSSQL database. I have attached screenshots of the credential settings for the device as well as two screenshots of the actual login process
Data Not Collected Errors
OpManager, or the response from the server, occasionally misses device polls, setting off alerts within OpManager. Is there a way to set this so it'll take 10-20 misses before it shows the Yellow error message within OpManager. I have to spend too much time cleaning these out when its only one miss every once in a while. thanks.
How to delete SMS cue ?
Hi, I've disconnected sms modem serial port for about 2 months just because a TEST PHASE...now i've reconnected it and i'm receiving all the old sms cue... how to remove the SMS cue ???
Does Microsoft Windows 2000/2003 send ColdStart or WarmStart trap when they started ?
Does Microsoft Windows 2000/2003 send ColdStart or WarmStart trap when they started ? I use a small tool to test this, when i restart snmp service, i got 3 traps: linkUp(3) with variable 1.3.6.1.2.1.2.2.1.1.1 with value 1 linkUp(3) with variable 1.3.6.1.2.1.2.2.1.1.5 with value 5 linkDown(2) with variable 1.3.6.1.2.1.2.2.1.1.65543 with value 65543 I did not receive any coldStart or warmStart trap. My small tool can handle only SNMPv1 trap, does Windows send SNMPv2 coldStart trap ?
Serious Support issue/attitude
I need someone from Adventnet to contact me ASAP regarding a support case we tried to open with your company. My IT person called your support line to get help regarding disk space alarms not being caught and the person on the other end of the phone did not seem very knowledgeable nor interested in resolving our issue. At one point during the call, your support person said "I have other customers I need to attend to right now". Are we not a customer? The person on the other end of the phone would
Why Upgrade?
We are currently running OpManager Premium v. 7205. We are looking to upgrade to v 8, but are unsure as to the stability of the process, and the affect this will have on our current build and data as we have several custom monitors. Can you advise as to the advantages of upgrading, and the process involved?
Managed ports & status polling issue; switch ports re-po
Hello, I am in the process of adding several Cisco Catalyst switches to our OpManager monitoring package. We are running build 8005. I am experiencing a very inconvenient issue that I want to make known and resolved. To start, I have added 18 Catalyst switches that we'll be monitoring. I have gone in on several of those switches and went to the "configure ports" section where I've unmanaged ports I don't need to monitor as well as removed "status poll" from some of the managed ports (not all). I
Problems SNMP Servers
Hello. My name is Jaime and i use opmanager 7 trial. I have 7 severs and only is monitoring 1 ( where is server opmanager). In the other hability snmp with the community create and when test the credential is ok in snmp but when add one monitor (example disk utilization), i have this error: El monitor no responde al requerimiento de prueba Resumen Nombre de Dispositive serve Nombre del Monitor DiskUtilization Protocolo SNMP OID .1.3.6.1.2.1.25.2.3.1.6 Posibles razones 1. Chequear si SNMP est� habilitado
How to delete SMS cue ?
Hi, I've disconnected sms modem serial port for about 2 months just because a TEST PHASE...now i've reconnected it and i'm receiving all the old sms cue... how to remove the SMS cue ???
Creating monitors on different times of the day
I had the following problem: some services (on this case, at night) will be shutdown everynight because of the task of backup that is implemented on several servers - how can I disable the monitor between this hours ? Thanks, jose santos :cry:
Avaya IP Office licence monitor?
Hello, I am currently trying to implement an snmp monitor, that will alert me when the licence status changes from valid to invalid. However i cant seem to get the oid working. I am using: .1.3.6.1.4.1.6889.2.2.1.2.0.25 Could anyone assist please?
Database size over doubled since the upgrade to 8
I don't see anything on the first couple pages, is anyone else experiencing this? We've gone from 2.4GB to 5.8GB in a month or two and it's been running for a couple years just fine. Anyone?
User management in OPManager 8
Hello, I migrated on OP Manager 8 latest build 8006, now I would like to set users in OP Manager. I created one user with read access, I discovered few things missing : 1 - When you select business views, user cannot see any dashbords only business view 2 - In dashbord created, I put widget favourite reports but user with read only right cannot see these reports as reports are linked with account who have created reports 3 - user with read access cannot created any favorite reports for himself. It
Add Widgets to Dashboard (Nothing to choose from)
Hello, When I try to add widgets to a dashboard I have nothing to choose from ??? I have installed Opmanager 8006. Regards, Marck
IP Address Manager - support group / subnet hierarchy in tree
In "IP Address Manager" -> "Network Details" view: The tree display on the left should support a true hierarchy of: - networks: for subnetting (breaking a network into smaller parts = subnets), subnets should be displayed as a child of the original network, and only the subnets should get scanned - groups: currently, groups cannot be nested, though in many companies organizational units are
Device Not Supported to add the Voip monitor
Hello People, I am trying to set up VoIP monitoring between two routers. I get the error of Device Not Supported to add the Voip monitor when I look at configuration history. I have set IP SLA response command at each router. Is there anything else I should be checking? Thanks Leigh
Next Page