Can I generate an alarm for a compliance violation?
Can I generate an alarm for a compliance violation? Basically I'm looking to automate the remediation of network devices with configlets but I can't find a way of doing this currently. I can generate the compliance report and manually execute the script
How to create a new device group in NCM
it just doenst work... i get an error all the time. therefore i can't create a CLI configlet.. The input specified for the ComponentSelection parameter does not match the required pattern. Die für den Parameter ComponentSelection angegebene Eingabe stimmt
Problem with Firmware Ugprade NCM to Aruba CX
Hi there, first of all. I'm new ;) Greetings. So i have a problem with NCM and upgrading firmware to a Aruba CX6000 Series Switch. i tried all possible ways. tftp, sftp ans scp. The script in NCM: $device.execute("no page") $device.execute("copy tftp://IP
Can the NCM be used to to check things? e.g. to address Cisco FN - 72511
Hi All, Can the NCM be used to check things and flag if it does not meet minimum reequipments? For instance, SSH RSA key size is at least 2048? Field Notice: FN - 72511 - RSA Keys Less Than 2048 Bits Are Not Supported for SSH in Cisco IOS XE Release 17.11.1
Per port Cisco ISE compliance checks?
I'm having issues with writing "Advanced Custom Criteria" that works to run compliance checks on each port of a Cisco switch. Basically, I would like to write the criteria to check if an interface has all the correct ISE configuration on each port unless
Large Image Upload using Configlets
Hi all, i have troubles figuring out a right way to automate image upload to Cisco Nexus Switches. The images are large (~1,9Gb) and it takes significant amount of time to get it through. The default timeout of Commands in Configlets (Advanced Script
Cisco WLAN Controller
Hi, we have 2 Cisco WLAN Controllers (5520 and 3504) which I would like to add to NCM via SSH. Unfortunately, I can't get a working connection to the WLCs although I can see that NCM is connected to the device, so there is no issue with the network, credentials
NCM
s there a way to delete devices from NCM backup but leave them in monitoring in op manager plus? if so how?
Regarding Cisco WLC Backup
Hello，We have recently encountered the following error when backing up WLC, while other Cisco devices are backing up normally. This is our version. Build number 12.6.121
How to avoid the 'toggle tax' from affecting your network configuration management
Toggle tax is a term used to define the loss of productivity users experience when switching or toggling between apps, tools, or websites. Each additional app, tool, or screen the user has to switch between necessitates a certain amount of 'context switching'
Have thoughts on observability? Take the survey and earn a $10 gift card.
Hello there, We're inviting IT leaders—IT leaders, IT/network admin, and software/DevOps engineer—to take the 2025 Observability Survey we hold at ManageEngine, an initiative to create an observability report with ground-level insights into adoption,
Restrict configlet based on device details
Is there a way to set up a configlet so that it will only run on a specific device model or OS version?
Is there any way to backup HP 1910 Switch configuration
Hello. I have some troubles to make DeviceExpert backup configuration of hp 1910 switch. No matter what vendor I've choosed it doesn't work. To backup running config manually I should login to switch via telnet or ssh, then type command "_cmdline-mode on", type "y" to confirm that and after type password "512900". And only after that manipulations I allowed to run "backup startup-configuration to A.B.C.D <filename>.cfg" I've tried different combinaion, when added ssh\telnet credentials. When I added
How to remove custom Device Template
How I can remove custom Device Template from NCM? I found folder with templates, but my template isn't there /opt/ManageEngine/OpManagerProbe/conf/ncm/deviceconfig/devicetemplates Best regards
REST API
Hello, Where I can find documentations for REST API? https://www.manageengine.com/network-configuration-manager/help/rest-api-ncm.html - API requests don't work from this website Best regards
Does ManageEngine Support AMD Servers for Network Monitoring?
Hi everyone, I’m currently considering deploying AMD servers for network monitoring and management, and I’d like to know if ManageEngine software fully supports AMD servers for these tasks. Are there any known compatibility issues or special considerations
[Free training] Learn how to back up configurations, track changes, automate tasks, and stay compliant
In today's fast-paced IT environments, network disasters can lead to substantial financial losses, often stemming from improper configuration changes, compliance breaches, and configuration conflicts. However, these issues can be mitigated and even prevented
Cisco Small Business Switch Sync Configuration
I am trying to add Sync Configuration to the Cisco Small Business Switch NCM device template, but it fails because it requires a "y"confirmation to proceed: SW1# write mem Overwrite file [startup-config].... (Y/N)[N] ? I am trying to use the correct Prompt
FTP - Network Configuration Manager
Hi I am planning to use FTP to take a backup of a device using Network Configuration Manager. Just want to know if FTP is supported in NCM & if so where and how to enable it ?
Gain key insights for effortlessly managing network configurations with Network Configuration Manager
Hello there, Network configurations are the backbone of your network infrastructure, and managing them manually or without adequate tools is challenging and prone to errors. Join our free training sessions to discover the full potential of Network Configuration
AD Authentication
Hello, I'm configuring Network Configuration Manager and trying to get AD Authentication working. First I tested with all users defined in AD: In Settings > Authentication > Windows Domains, I created my Domain with "Domain Name", "Domain Controller",
ASR-1002x Cannot run NCM script
I'm trying to run a simple NCM script on a group of routers (2 in the group are ASR-1002x). Job fails on these devcies only but is successful on the other routers. Does anyone know if the ASR-1002x can support NCM? I'm getting the error response back
TFTP Configuration Backup Location
Can you provide a tftp backup directory? Or provide an operation method for exporting network configurations
Unexpected behavior for NCM
Dear team, Could you please advise on the issue below? Sometimes I can see that backup failed with this output when NCM try to backup config. But backup will be finished successfully in next try with no changes... If I try to execute terminal datadump
Connect with us at ManageEngine North America User Conference
The ManageEngine User Conference is back in the USA, and we are super excited to meet our customers. This year, the conference will take place on May 14 and 15 in Newark, New Jersey and Sept. 19 and 20 in San Diego, California. New Jersey Date: May 14-15,
Compliance Scan - Create Exception
Is there any way to create an exception rule for a compliance scan? Meaning, if there is a setting that will fail a CIS rule for Cisco IOS - because that is how it is deliberately configured on a network device - is there a way that a compliance scan
Applying credentials for Network Configuration Manager
[White paper] How is IPAM helping simplify modern networking needs?
Ever feel like you're constantly playing catch-up with your network? AI, IoT, digital transformation, and hybrid networking are causing a huge influx of data, applications, and devices into your network, and now more than ever. This can make your network
Network device backup failed
Hello, Recently, there have been frequent network device backup failures. The current solution is to restart the entire OPM service. Is there a small-scale service restart method available Ver:126121
FORTIGATE NCM fails after upgrade from 7.012 to 7.0.14
Hello, We have a series of Fortigate Firewall that is backed up by Opmanager NCM and was working fine until recently when we upgraded OS from 7.0.12 to 7.0.14. We have one Fortigate on 7.0.12 and the backup is working fine. The credentials remain the
ManageEngine NCM REST API v2 Documentation
In a previous post ("ManageEngine NCM REST API Get issues"") there was mention that there was "In our latest versions, we have v2 API" Is there any documentation on the v2 APIs? What are the differences between the v1 and v2 apis calls? What is the roadmap
Backup Sonicwall TZ Series
I am having issues with NCM/Firewall Analyzer in OPM using credentials for SonicWall TZ370. I test credentials but it fails on the process of accessing as admin/enable mode. With Sonicwall SSH interface, I can manually access the configure prompt but
Network Configuration Manager not Detecting Desktop PCs
Hi everyone, I hope you're all doing well. I'm currently facing an issue with the Network Configuration Manager from ManageEngine, and I was hoping to get some assistance here. The problem I'm encountering is that the Network Configuration Manager doesn't
[Free Training] Gain invaluable insights and techniques for effortlessly managing network configurations with Network Configuration Manager
Hello there, Network configurations are the backbone of any network, emphasizing the importance of careful monitoring to ensure seamless operations. Join our free training sessions to delve into the capabilities of Network Configuration Manager, a comprehensive
API Call for device configuration
curl --location 'https://myserver.net/api/json/v2/ncmdevice/getCurrentConfig?apiKey=myapikey&deviceId=2661' I can pull the device list and and a few other items but trying to pull the current device configuration fails with a 404 error. Anyone able to
ManageEngine NCM REST API Get issues
Hello, I'm trying to make sense of the documentation for REST api usage in the NCM module (BUILD 12.7.259). From: https://www.manageengine.com/network-configuration-manager/help/rest-api-ncm.html This is the provided example: http://localhost:portnumber/api/json/<ModuleName>/<API
CLI Device Template
Hi, How can I manually assign a different device template? I have some Brocade G620 SAN switches that are being assigned the general "Brocade Switch" template which executes the wrong commands to get the running config. I need to force a change to the
Constant CVE alarms!
There are a few routers, switches and loadbalancers that I have that even though are set to Not Applicable, and I clear the alarms, the next day I get a flurry of new alarms for the NOT APPLICABLE! This is getting old. I only want alarms for actual NEW
[Free training] Acquire invaluable insights and techniques for seamlessly managing network configurations with Network Configuration Manager
Hello there, Network configurations serve as the foundation of any network, underscoring the need for vigilant oversight to ensure smooth operations. Attend our free training sessions to explore the use of Network Configuration Manager, an extensive network
SFTP Backup files
Hello, Is it possible to backup network device and generate a file and sent it with a secure tranfer to a SFTP server (local) ? NCM and SFTP server will me the same server. Thanks
Next Page