Mass-change switchport utilization threshold?
Hello there, We are trying out OpManager and comparing to Zenoss, and WhatsUpGold. So far we like OpManager a lot. Just about to say we like it more than the other two solutions. So to start, props to this solution. It is very good One issue I'm running into is excessive alarms on my switches. I have 4 cisco 3750 switch stacks. Each stack has 5 or 6 switches in it, adding up to just over 1000 ports. I get a crap load of alerts saying that switch ports are exceeding 30% utilization. That seems like
Log file Monitoring
Hi Team, i wanted to monitor logs of a application. it works fine when the logs are generated in ".txt" format. but my application is generating logs in ".log" format which Agent unable raise the alert . Can u please tell me what i am doing wrong? Regards, srikanth
OpManager9: Service Monitor - Edit Error!
Dear Support, Under a host service monitor, I added RDP (TCP 3389) monitoring and it working fine, later I configured the threshold value and save, next click on edit, it just shown Error!, suspect the figure might cause this issue? Refer to the attachments and please advise how to rectify this issue? Thanks in advanced! Regards, gary
Delays in getting email alerts
Hi, Our Opmanager email alerts are getting delayed (They are displayed on the Alerts page in time though). They were 7 hours delayed on Monday morning and we restarted the service and it came back, but over the course of the day they got more and more behind. The same was true yesterday and by the days end it was 9 hours behind. I upgraded to 10.2 last night in the hopes this would correct it, but this morning the latest alert I have fired at 03:07am but arrived by email at 08:26am. Our email system
Wireless and ethernet interface monitoring of PC running Win7
Hi Team, I was wonder if it is possible that we have PC computers connected to internet using ethernet port and we have wifi enabled on a adhoc network where we have PC server running opmanager, is it possible that opmanager can monitor throughput on ethernet interface of PC computers. Regards, Adnan
OpManager integrate SDP with ssl
We are can't integrate SDP with ssl to opmanager. We are using sdp.keystore from SDP and edit file ssl_servicedesk.bat to provid correct keystore. OpManager.truststore was create but SDP didn't integrated. What wrong? Our ssl_servicedesk.bat look like: @echo on set NMS_HOME=%1 if not exist D:\OpManager\conf\sdp.keystore goto keyStoreMessage if exist sdp_cert.txt del sdp_cert.txt D:\OpManager\jre\bin\keytool -export -v -rfc -alias sdp_alias -file sdp_cert.txt -keystore D:\OpManager\conf\sdp.keystore
MIB's
Hi Jim, We want to acquire the services of a specialist to help us with MIB files for Avaya/Nortel switches 4800 series for Opmanager Can you do that or do you know someone else? Regards, Billey
Switch Port Mapper Port Description
Hi I have just done a Switch Port Mapper on by Cisco 4500 Core switches and under description it has come back with the port number rather than the actual port description that has been applied. Can this be changed? If so how?
OpManager 10 Free Version
I have installed OpManager 10 Free Version on a Linux host and doesn't seem to be collecting stats. I am able to snmpwalk from the host and use the mib browser within OpManager to pull information from devices. Is a license required to run the free version?
MIB Server OPManager
We want to acquire the services of a specialist to help us with MIB files for server : HP BL460c G1 HP BL460c G6 HP RX6600 HP RX8640 HP ML110 G5, G3 RX 4640 DELL PE2950 UCS B200 M2 the series for Opmanager thanks, sendi
OpManager9: Network Interfaces not detected
Hi, I am new to OpManager, current we have a site is using OpMgr9 for servers monitoring, I have few servers can be monitored however unable to detect network interfaces even with Rediscovery... it will shown below message Unable to rediscover the interfaces. Possible reasons: The device is possibly down. SNMP may not be running in the device. SNMP parameters may be wrong.Verified the SNMP services is running fine... Any idea how to rectify this issue... Thanks in advanced! Regards, Gary
Eventlog record absence as alarm
Good day. Is it possible to configure the OpManager to generate an alarm if event record in Eventlog is absent? For example we're expecting that in period 10:00-11:00 a task must be finished. Only 3 events are possible: 1) task successfuly completed 2) task failed (critical event) 3) absent event at all (critical or warning event) 2 and 3 should be monitored.
Attach files to emails from OpManager workflow
Is it possible to create a workflow that attaches files from a server after they are created?
SNMP Vserver CurrentConnections monitor for Citrix Netscaler
Hi, I'm using opmanager enterprise 10200, and trying to monitor Citrix Netscaler Vserver CurrentConnections. When I register and check result for this monitor, I can't see some instance name as vserver name. It is shown as mib number like below table. Do you have any idea to solve this problem? sojournweb 7533 7348 517 8166 3992.8 > vserver name through 0 0 0 0 0.0 url 2 0 0 8 0.2 vitempage 9856 9412 858 10649 5519.3 .4.115.101.108.108 45 54 0 1032 20.1 > mib numbers .5.105.109.97.103.101
contextless url
can the be done with opmanager http://thinkinginsoftware.blogspot.com.au/2011/02/hide-context-url-in-tomcat.html Thanks, Stephen
how to configure dependencies for one device
Hi We have OPManager installed, I have already configured the dependencies for several devices behind a router or switch. When the last one goes down, no alertes from devices that are behind it. I am looking now for configuring the same thing for one device. I mean for one server with several services monitored on it and I want if the server goes down, I get only one alert for the box but no alerts for all its monitored services. My OPManager version is 11100 recently installed. is the
Specifying MSMQ Thresholds Unable to test
I'm trying to monitor a MSMQ on a windows 2003 server. I add the monitor without any problem through the device templates and am able to test the monitor successfully. As soon as I add thresholds to the monitor and then try and test the monitor again I get "The Monitor did not respond to the test request " Any help would be appreciated.
Traffic Analysis of Ethernet Interface Interval
Hi, We are using op manager version 7 running on Windows XP and we use the Traffic Analysis of Ethernet Interface graph to see how much bandwidth each port is using. We have some switches that work fine and we get monitoring intervals of around 1-2 seconds but some switches are completely random, an example of the monitoring intervals are below. I cant see any issues and they are both setup the same. Can anyone help? Here is the link for the graph we are able to see: http://OpmanagerIP:8060/devices/InterfaceGraphZoom.do?InterfaceName=SWITCHIPADDRESS_Port36&hcTraffic=false&timePeriod=Today&graphName=Traffic&keepDivOpen=true
If I use an SNMP Trap to trigger a workflow, can I access the trap details in the workflow objects?
If I use an incoming SNMP Trap to trigger a workflow, can I access the trap details in the workflow objects? Using Build 11100 KR Tim
Graphics in realtime
I wonder how the realtime capture the information, and how it captures when the device goes down.
Unable to send due to java.net.SocketTimeoutException
Hi.. Getting the following error when trying to test email config: Unable to send due to java.net.SocketTimeoutException Have tried a number of POP3 and SMTP options/accounts. Any ideas? Clive
How do I get updates on new versions of Opmanager via Email
Can i subscribe to get email updates every time a new release of OpManager is released?
Problems with SMS via GSM modem
Hi, I have 30 days trial version of OpManager 10100 on Windows 2008 r2 (64 bit). And I'd like to send sms notification. So I connected gsm modem hsdpa and OpManager detected it as HSPAUSBModem, model 33. So now in SMS server settings I have Modem Manufacturer : HSPAUSBModem Modem Model : 33 Battery Status : 100% Signal Status : 52% Status : Connected When I added sms profile and tested it I got the message that sms was sent successfully but no sms was received. Even when I unpluged the modem and
Opmanager 9410
Dears Team, Opmanager 9410 currently using since 15 days not getting alerts Disk free threshold alerts. Earlier it was getting properly alerts disk free threshold but now is not getting? What is the reason.. Regards, Hussian
opmanager admin password reset linux
I forgot my opmanager admin password. How can I resem my opmanager admin password on linux?
Syslog rule
Hi, i would like to uses opmanager to receive syslog and generate alarm. But not success. I can view the syslog via opmanager's syslog viewer, and already set the rule. But still cannot generate the syslog alarm. I am using opmanager build 10000. syslog eg. %SYS-5-CONFIG_I: Configured from........... rule eg. rule name:CiscoConfig Facility Name:Any Severity:Notice, Information Match Text: SYS-5-CONFIG_I Alert Severity: Critical AlarmMessage: $Message
opmanager admin password reset
how can ı reset my opmanager admin password on linux.
opmanager admin password reset
How can I reset my opmanager admin password on linux.
Chakradhar
i was added 20 hp switches and 10 Cisco switches in Opmanager. but layer 2 topology not showing all the devices. it showing all Ciscodevices,HP Procurve 1810 and 1800 switches not showing
Partition Details of the Device (%) WMI monitor produces incorrect percentage
We have the above WMI monitor on a 15 minute interval and as you will see from the example data below we are getting impossibly high percentages. Our critical alert threshold is set to 95% therefore an alert is being falsely generated and cleared at each interval: Date and Time C: Percentage 23 Dec 2013 03:41:54 PM GMT 22772.0 23 Dec 2013 03:41:54 PM GMT 71.0 23 Dec 2013 03:26:52 PM GMT 71.0 23 Dec 2013 03:26:52 PM GMT 22774.0 23 Dec 2013 03:11:53 PM GMT 22774.0 23 Dec 2013 03:11:52
OpManager Defaulting to http://localhost:8060 When Viewed Remotely
OpManager is working fine when viewed on the server it is on. However, when I try to access it from any other box the url defaults to http://localhost:8060 even when I put in http://10.31.147.71:8060 This prevents the pages from loading. Is there a setting somewhere that I can make the url default to http://10.31.147.71 instead of http://localhost?
widget 'real time graphs for CPU' stops drawing somewhy
Hi guys, in my opinion OPManager is a great product, congratulations! I installed OPManager10 to monitor several Windows 2008R2 servers with SQL Servers, registered windows servers in OPManager, defined performance counters to monitor with WMI, created several dashboards and CCTV view. It worked fine for a while, but in time widget 'real time graphs for CPU' began to stop refreshing for 3 servers only somewhy, I mean after OPManager service is restarted 'real time graphs for CPU' draws CPU Usage
Monitoring ServiceDesk ticket volumes in OpManager
Hi, Is there anyway of monitoring ServiceDesk ticket volumes with a custom dashboard in OpManager? I have looked through Google without finding any answers, so thought I would throw it out to see if anyone on the forums knows a way of doing this? Any help would be greatly appreciated!
Backup e Restore data from apmanager plugin
hi, I have installed opmanager with its plugin apmanager. what is the correct procedure to backup and restore the settings and monitors configured ON THE APMANAGER plugin? I tried with opmanager backup but does not save the data to the application. I tried it with the backup apmanager but it does not work and writes a file to 0 Kb There is a guide to follow?
Is it possible to monitorize a .bat file?
Hello. I want to know if is it possible to monitorize a .bat file. I want to configure an alarm when the number of instances of that .bat file is = 0. Many thanks.
Not display Monitor of device info of memory and CPU
Hi all ! I connectioned Fortimail to Opmanager used SNMP. in Fortimail, I enabled SNMP in Opmanager, I created new template, Browses file MIB of Fortimail, and test SNMP with Fortimail passed. But, Why info of Fortimail not display in Opmanager. So, Can you help me. Thank and Regards !
Error when add new interface
Hi, After I migrate the database to postgresql, I have the following problem: When I try to add a new interface, OpManager tells me that the interface was added with success but it does not appear in the list of interfaces. Below are the steps I followed: How can I fix this? Regards, Bruno Lorensi
So what do you guys think of the new UI (beta)?
Personally I was sad to see that a new UI is coming. One of the reasons why I chose OpManager in the first place was because of it's simple and intuitive UI. I like the old interface - I think it's straight-forward and very easy to get an overview of things. Configuration wise it's never difficult to find the settings etc. But am I the only one who will miss the old UI once it's gone?
Missing the Windows Service Monitors Tab
Hello. All of my servers are VMs but some do not have the Windows Service Monitors item in the list on the Monitors tab. Why is this? I am using WMI successfully. Our edition is "Essential" and our build number is 10200. Thanks, Joe
Business view in FULL screen. NO BORDERS
Hi, I plan to display the OpManager Business view screen in the NOC on a big screen. Is there a way of displaying just the screen without any borders and tabs. Thanks
Next Page