cpu utillization not view
dear all' how to view cpu utillization ?? Can anyone help me with this case... Thanks regards M.tohir
ifAdminStatus on Switchport???
Hi all 1st post :) We have a few HP switches in our environment. I have added them into OpManager and all is well. My problem is, if I put a port into "Disable" status, I want OpManager to reflect this, and NOT to state that the switchport is "Down". Right now it is not reflecting this state. Any ideas? cheers will
Device Template for storage devices
I'm looking for a device template for storage devices, specifically San's. Vendor IBM, Dell or HP. I can't create one because there is no category for storage devices. Can I create a category? Is there a recent update for the resident device templates with OpManager? Thanks
Help required with maps
How can i display the complete map of my network devices.in the default map it does not show it,what i am looking for is the network devices and their links. e.g PC--------SWITCH----->FIREWAL-------->ROUTER ! ! PC
Rebadged Lexmark Printer (Dell 1710N)
HI Everyone Trying to get OpManager to recognise a Rebadged Lexmark Printer which is used by Dell 1700 series. Comes up when I try and add a new device as the ODI already being used by the Lexmark device. Is there a way to differentiate between the two as it is being shown in Opmanager as a Lexmark when it is a Dell printer ????? Thanks Andrew Loughnan St Joseph's College, geelong Australia
Changing body of Clear Message
Hi Apologies if this has been covered a lot but did a search and couldn't see it on the forums I can change the content of the message body in an alarm message by using the variables supplied and free text - which is great What I want to know is can I change the message body of the Clear message At present its "Data Files Size is now back to normal, valuses..." I would like to edit this to a simpler message which more matches the set alarms messages. Is this possible?
Switch Port Mapper community field is gone.
Switch Port Mapper community field is gone after upgrade to 7200. After clicking Show Mapping, the ip address adn DNS are all empty.
Switch Port Mapper - Multiple Server/Router IPs?
I have both PCs and IP phones plugged into the switches. However, resolution comes from 2 sources/VLANs (VLANx/10.x.x.x for PCs & VLANxx/192.x.x.x for IP phones). Plugging each server/router IP into the field allows for the devices (PC or phones) associated with that subnet to propagate the IP/DNS. I'd like to see ALL the port info for both subnets in a single window. Is there a delimiter that can be used to give both server/router IPs simultaneously or another method to accomplish this?
Misconfigured devices, errors etc.
Hi all, I was wondering if there is a way to get Opmanager to report on devices that does not have SNMP set up properly, for example the community string is wrong, or the device does not allow SNMP access from opmanager. Opmanager should not report the actual problem, just that there is one. Also if WMI is not accessible due to logon failures etc. If there are 100s of devices, you sometimes find yourself needing interface graphs, disk usage etc. but the device has some config problem that you did
Problems to start up the program
Hi there! We are trying to start up the OpManager v6 and a message appears telling us that "some of the tables are corrupted. repairDB and then ReInitialize the program". Our problem is that this is not working anyways. The Repair script is not fixing anything... And to be honest, I don�t wanna restore the DB because we haven�t made a backup since months... :( So, Could you please give me another solution?? And do u know why is this happening? Thank you very much for your attention!! Kind Regards
Rename device with system.sysName instead IP adress
Hi, I would like to know if is possible to print device name with system.sysname name from MIB instead of IP adress, It would be great to be abble to do this automatically without using the GUI for every host. Thanks
Event Log Rules
We had created a new Event Log rule (for the Application Log) with just Event Type = Error checked off, and Alert with Severity = Critical. This was almost the same as the predefined "Any Application Failure" which has Event Type = Error and Warning checked off. The new event log rule seemed to be working, but now it is not, and we cannot figure out why. We're getting plenty of Application log events logged with type Error, and users that have the "Any Application Failure" rule in their notification
NumberFormatException when calling refreshObject
Hi! Sometimes I'm getting a NumberFormatException (null) when calling TopoApi.refreshObject(). Why is that and what goes wrong? Here's the stack trace: java.lang.NumberFormatException: null at java.lang.Integer.parseInt(Integer.java:415) at java.lang.Integer.parseInt(Integer.java:497) at com.adventnet.nms.topodb.SetupNode.addSNMPInterface(SetupNode.java:985) at com.adventnet.nms.topodb.SetupNode.performV3Discovery(SetupNode.java:709) at com.adventnet.nms.topodb.SetupNode.pingAddress(SetupNode.java:3677)
SNMPTrap sent from object/devices not registered
I'm sure that if devices IP is not added to OpManager any snmptrap receives will not appear under alarm tab. But is there a way for us to check if this is happening? Might be inside the log files? I need to know IP address sending trap to OpManager but is not registered as monitored devices.
OpManager 7 Traffic graphs show NA
HI, I have been trialing OpManager 7 for a few weeks and I have been very impressed up untill the today. All of my traffic graphs are showing NA when I look the snapshot (Router Infrastructure Snapshot) If I drill down into the grap by selecting the interface I can see the traffic (so the graph is still woking). Please see attached picture
Interface Graphs not view
dear all We have a problem with the Newtowrk Interface Graph with all devices. The Graph doesnt show and the following message is displayed : Sorry, no data available for Graph. Try other options thanks regards M.tohir
how can i set cli timeout?
i have a linux server with ssh, i add a monitor user,and i can use the user to login on server with ssh,but opmanager always report cli timeout.i found the time of login on linux server is up to 10 sec. so i want change the cli time.how can i do it?
Web Alarm - configuratation
Is there a way to change the sound that is generated for the web alarm, and also to be able to create more than one web alarm with different sounds/wave files..
XP service monitor newbie
I would like to monitor a custom service running on a Windows XP computer from OpManager. However, the Add monitor option is not present for desktops. How do I do this? TIA Steve
Picking one row in a SNMP table
Hi everyone Ive setup a custom SNMP monitor but having problems returning exactly what i want. The OID returns two columns: a process name, and a value for that process. The rows are lots of different processes. I however only want one particular process. If i do a table view from MIB browser i can see the row i want but when i set up the monitor i dont know how to specify a particular row from the table so it just returns them all. Please help! Thanks, Chris
How may Business Snapshot are allowed?
How may Business Snapshot are allowed?
Cisco Pix Interface not added
I recently upgraded to build 7202. I have two PIX firewalls and when I go to monitor either one Opmanager does not show my internal interface. When I try to rediscover the interfaces it properly identifies the interface but when I try to add them they do not show up.
SNMP dont get connection but WMI runs
hello, from germany, ich have install the trial version on a server 2003 system. before i have install the snmp service from the installation-cd. the service are running on the system. when i login from a console like a laptop and configure the services and process-scanning i dont get the connection to the server about the snmp credential. the WMI login are successful. i dont have found some information. or i dont have translate it wrong for me. Have someone a tip or solution for me? Must i activate
MSSQL monitoring
How do I add MSSQL monitoring for different databases? I purchased Premium Edition Single Installation for 50 devices, so I would think I should be able to monitor databases & Active Directory, I just cannot figure out how to enable the monitoring.
Issue adding new network device
I recently upgraded to the 7201 and now every time that I add a new network device, it is added with no display name. Since there is no name, I cannot select the default name (usually the IP address or DNS name???) to rename the device according to the standard that we have been using. These devices don't have DNS entries, but that has never been a problem in the past? Has anyone else seen this? Any Suggestions? Thanks, Bryan
Please HELP urgent!!!!: Error linux server via ssh graph
When I try to add a graph (i.e. cpu utilization) for a linux server via ssh, I get the following error: SshTools / log4j jar not present in classpath. Please download the sshtools-j2ssh-0.0.4-alpha-bin.tar.gz/zip from url "http://prdownloads.sourceforge.net/sshtools" and set classpath to jaxb, log4j and sshtools jars. [ Telnet-FreeDiskSpaceInMB ] My S.O where are my instalation is Windows 2003. I've the file sshtools-j2ssh-0.0.4-alpha-bin.zip it has the files jaxb, log4j and sshtools jars. I've also
How do I configure Process Monitor Thresholds?
Hello, I'm a little confused how to configure Process Monitor to keep an eye on a few processes. I'd like to make sure that they don't drop below 1, ever. I have configured the following settings: Threshold Details: Instance count = value 1, rearm value 1, consecutive times 1 However, with this configured I'm receiving the following Attention Alarm: Instance Count Threshold violated for src_dist process. Current value is 1 Does anyone know how to configure the process monitor to make sure that there
Problem in Vanguard
Hi, One of our client carry vanguard motorola, as usual we follow the add template in order to add the devices. Though we follow the steps in adding template, we still encountered problem. The devices was already snmp enabled. other work around or what is the reason why we encountered such kind of error? Please advice, Irene
CPU Utilization - Geting started - Newbie question
I have just loaded the software and am tring to get the above stats working. I can find how to get the opmanager side going but not the client side. At the moment just testign with 1 windows xp client so do I just add smtp ? Does this need configuring ? Thanks,
I use the Run Program at the OpManager.
Dear all, I use the Run Program at the OpManager. I created the Profile as follows. Test_No1. ---------------------------------------------------- Profile Name: OPMTest Command Name: C:\SMSTest\SSMSTest.cmd Program Arguments: $message ---------------------------------------------------- The test of Test_No1 is successed. And I tested as follows (Test_No2). ---------------------------------------------------- Profile Name: OPMTest Command Name: C:\SMSTest\SSMSTest.cmd Program Arguments: $displayName
I want to access Mysql of OPM using the java language.
Dear all, I want to access MySQL of OpManager using the java language. But I saw that error message "java.sql.SQLException: Table 'opmanagerdb.user_t' doesn't exist". I attached a snapshot about a source and error message. I want solution. Thank you in advance for help me. Ko Young Suk Telemant Corp.
Invalid License File Error
I am getting an Invalid License File error when I try and start the OPManager. Anyone get this error or know how to fix it? Thanks!
Domain Controller Category Problem
Hello, i have opmanager 7, build 7010, and i dont have licensing for AD Monitoring. The problem is that in discovery it found a DC and put it under Domain Controller Category and doesnt let me access it. When i click on it, under the Domain Controller View, is gives me the message that i dont have the add on licence. So i go to Servers and click "import". I import it and it disappeard automatically, and now it shows the following error: Status Message Unable to fetch Managed Object details for the
Opmanager serive won't start
ve followed the basic troubleshooting steps I found on this board but I've had no luck in getting my opmanager to start up after a shutdwon earlier this week. I've uninstalled and reinstalled the service, done repairdb.bat and startOpManagerServer.bat. Also here are the logs as well. Thanks. D:\Program Files (x86)\AdventNet\ME\OpManager\bin>StartOpManagerServer.bat inside addon check Windows 2003 Checking for the availablity of the Primary Server in the Database. Found an ent ry. Trying to connect
I not use the MySQL of Applications Manager.
Dear all, I not use the MySQL of Applications Manager. So I want to the other MySQL. I installed a MySQL ver 5. I want a configuration way(xxx.conf?). Thanks, Telemant Corp.
No notification received
hello there. I have setup Notification for Polls and SNMP 1 case, (picture 1 and 2) Ihave configured when OpManager receives poll(s), send a notificaiton to me, 2 case (picture 3 and 4) I have configured when windows services such as SNMP Service went down, send a notificaiton to me. I have not received any notification. email setting and test is fine. Any idea??? Thanks in advance.
Problem with downtime scheduler
Hello I have a downtime scheduled for several devices. When I add a second schedule and select a device, these devices appear in the first schedule instead of the devices selected for that schedule. The same thing happens the other way. I can therefor only have one schedule running with a set of devices. Rainer
Avaya MIB Traps
I have been able to load the Avaya g3mib20_asn1.txt (CM2.0) into the mib browser in Opmanager 7, but I can't parse it. My question is there anyone using Opmanager monitoring Avaya S87xx media servers and able to parse this mib? Thanks
Network Utilization Report in OpManager
Network Utilization Report How would I be able to gather network utilization reports on all of my site links? :?:
We want to run specific program using Script in OpManager.
Dear OPM support teams, We want to run specific program using Script in OpManager. That is to say, we want to run MySQL command(ex, Insert) using Script. - We know that script takes the function of the trigger. - We want run a MySQL using Script in the Notification Profile of the OpManager. - We use offered MySQL at the OpManager. Possible? If yes, we want sample example source (ex, Get values using Insert command in DB). Our customer was urgent now. So we want fast reply. Thank you in advance for
Next Page