Receiving alert on a non monitored port
Hi, i still receive link status alert for a non monitored port on a 3750 cisco switch. SNMP trap is on (snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart) but not for the interface 8 . I have : interface FastEthernet1/0/8 no snmp trap link-status And I still receive : Trouble d�c. 01,2005 02:12:43 PM .1.3.6.1.4.1.9.9.41.1.2.3.1.2.543: LINK, .1.3.6.1.4.1.9.9.41.1.2.3.1.3.543: 4, .1.3.6.1.4.1.9.9.41.1.2.3.1.4.543: UPDOWN, .1.3.6.1.4.1.9.9.41.1.2.3.1.5.543: Interface FastEthernet1/0/8,
Email Alert Messages Need Improvement
Below is an example of a email notification from opmanager for a threshold violation on a router. Message: Threshold violated : InterfaceInUtilization , Instance = 15 : Curent Value : 82 : Threshold value : 80 : Severity : Attention : Rearm Value: 75 Device: <omited by me> Category: Router Error Condition: Attention Generated at: Dec 05,2005 02:14:20 PM Given the number of routers and therefore interfaces we have in my organization its not practical for me to memorize what "instance 15" is on this
Downtime sheduler of OPManager
hy everybody, it consists possibility when i set a downtime shedule, that i a ordained group of serveradmins exclude. that is: these group becomes a device down message. backround: many of the watched server with opmanager starting new in the night. we have a lot of serveradmins, any wants the "device down" mail, other admins, don't like the daily down message! i know it realise with two notification profiles, one with trigger device misses 1 polls for the group that wants the "device down mail,
Clear HP 2824 password without reseting switch configuration
Can I clear HP procurve 2824 password without reseting switch configuration? Thanks for comment
When can new version be expected?
What is the current timetable for the release of the next version of OpManager? David.
Opmanager monitoring CPU Usage of Linux problem
I use Opmanager to monitor the CPU usage of Linux server, but the result always show "-1". Is the opmanager setting problem ? Thanks ~
Router Interface 100% Utilization
Is there any known issue that would cause my router interface (mulitlink - 4xT1 - 6Mbps) to show 100% utilization 97% of the time? The inbound/outbound traffic combined is not equal to the full circuit. Is there any way to verify what the software thinks the bandwidth of the circuit? Any help would be appreciated. Thanks.
Feature List for the next release
Hi All, Here is the list of major features planned for the next update, expected in a couple of months. 1. Custom Fields to Device/Interface Details 2. MSSQL support 3. CPU/Memory Diagnostics ( CPU/Memory Usage per process ) 4. Schedule Reports and much more. Keep posting your feedback and suggestions. Regards Karthik OpManager Support
Auto-login for Web Client
Hi, Currently, you have to login to access the Web Client. Is there an auto-login feature? I would like to use OpManager as network monitoring tool similar to HP Openview Network Node Manager and/or Intermapper, where users can just access the network maps and/or business views without logging in. Is this feature possible? This would be a great feature to have. Thanks.
opManager: Alert Notification and Escalation
I have found the following document recommending some steps towards 'Fail-safe alerting' in opManager: http://manageengine.adventnet.com/products/opmanager/fail-proof-alerting.html This document mentions alerting in different ways depending on the clock. But I am confused. From what I can tell there is no method to schedule alerts and escalation against the clock, or to a roster. There is no method to reliably escalate alerts at all in fact. Is there a method, or plugin that enables sensible alerting
stop notifying on acknowledged alarms
Under Admin>Alarm Escalation, we have a rule to notify on critical errors once an hour. However, this also notifies on alarms that have already been acknowledged. Maybe I misunderstand OpManager's concept of alarms and notification, but when I acknowledge an alarm, am I not telling the system "I know about this, please don't bug me again?"
Migrate opmanager to new server...
What's the best process for migrating to a new server? I am currently doing a DB backup on the existing server. Should I then just do a DB restore on the new target server? We would like this to be as seamless as possible and with no history loss of course. Cheers!
CISCO CATALYST 2970
We have OpsManager 5.6 and have recently added 2 CISCO catalyst 2970 which is a new switch from CISCO and it does not recognise some of the functions. Could you let us know how to get it working properly. Thanks. Peter Lye +65 91877911
snmp2c
I have installed adventnet manage engine free version.I have also loaded the mibs for Canopy devices .The devices support snmp2c .The device requires authentication before snmp query can be done. I could not find anywhere in settings for mib browser the option to specify root password.The same is given only for snmp3 . Can u let me know how to go about this..?
CATOS CPU Usage and AIX memory
Dear Kevin, I have checked the cpu usage OID of the Cisco Catalyst 6509 CATOS7.6 is OID1: .1.3.6.1.4.1.9.9.109.1.1.1.1.5.9 and I also added the customizing monitor via browser client. But when I test monitor for this device. The result is that the monitor is not response. The oid is: OID2: .1.3.6.1.4.1.9.9.109.1.1.1.1.5.9.0 please tell why the OID2 automatically add a ".0". I also use MibBrowser.sh to test the OID1: .1.3.6.1.4.1.9.9.109.1.1.1.1.5.9 and load CISCO-MIB. The testing result is OK. Please
Exchange 2000/2003 Monitor Deletion.
Hello, I accidentally added the Exchange 2000/2003 application monitor to a server that is not running Exchange and now I cannot delete it - there s no option to do this..... Adrian.
CPU Utilization using Linux/SSH
Few issues with the CPU resource monitor using Linux/SSH CLI. a) Is there any way to check the load average of a linux system istead of just cpu utilization. b) In the following case the threshold (90%) was violated at 6:38AM and the alert was sent out but i still havent received followup notification indicating the cpu utilization is back to normal. I tend to get it after few days. Is there something i need to configure properly? Date Time CPUUtilization Percentage Nov-28-05 16:23 27.0 Nov-28-05
Authentication Failure ?!
Anybody know why I get this error on servers? It happens about every 10-30 seconds or so. AuthenticationFailure : .1.3.6.1.4.1.311.1.1.3.1.2 <servername> Hardware: x86 Family 15 Model 2 Stepping 9 AT/AT COMPATIBLE - Software: Windows Version 5.2 (Build 3790 Multiprocessor Fr Need help. I have to correct this error! Totwart
Opmanager and Adventnet SNMP Linus Agent
Dear, I have resolve the NAT problem. Thx for your support. Now I have problems SNMP Agnet with OpManager. 1. The measurement of physical memory is invalid. 2. The CPU speedometer in OpManager is shown, but the disk utility and memory utility are not shown. I already make sure the port is opened, and I can browse the MIB. Would you help me, please. Thx
License Question
Hi, could you please let me understand which kind of license opmanager use for? My sample situation is: I have 10 servers to monitor on a customer office.. we want make avaiable a viewer profile for the customer EDP and an admin profile for us... Do I need to buy a "single installation licese fee for two user pack? Thanks in advance
SNMP info through a firewall
Hello: I have a boarder router on the outside of my firewall with SNMP configured on it. I can get the basic info from it but I can not get detailed traffic info. I configured the firewall to pass all the traffic, but still am not seeing all the info. For testing I opened UDP traffic and TCP traffic in both directions but no luck. Any ideas?
Incorrect OS
Hey-- congratulations on OpUtils, an excellent tool suite. You Indian programmers rock, I must admit. One small problem-- my XP machines show up as Windows 2000 in the System Snapshot. Are you aware of this? -- BF
Cisco Switch Alarm:port down - but port not managed?
HI there, I'm using OpManager 5.5 build 5510. I'm spending so much time trying to configure this to work that the cost is far outweighing the value for me. Please can you explain why my switch is sending me an alarm that FastEtho 0/10 is down when that port is not one of the ones enabled for port management? Interface down : ifIndex: 11, ifDescr: FastEthernet0/10, ifType: 6, .1.3.6.1.4.1.9.2.2.1.1.20.11: down
cisco 1700
I am trying to monitor the interfaces of my cisco 1700 router but am unable to see the interfaces within map mode, any help would be appreciated.
More than one email in Profile
Hi, I would like to know if it's possible to specified more than one email(To email address) in Profile or if I must define many profile for each email. Regards, Steve
Custom Monitors
I would like to monitor some of the counters available in the windows-nt-performance mib. I noticed on your oputils online demo that this mib was available however it is not included in the downloadable install of opmanager or oputils. 1) How can I get this mib? 2) How do I add this mib to opmanager? 3) Does it also need to be installed somehow on the hosts i wish to monitor?
Moving all configuration information to a new server
I am testing OpManager on a Windows box and have entered a lot of information. How can I move this set of information (servers/routers/printers/business views/alert rules/etc) to a new server (UNIX)? Is it as simple as copying some configuration files to the target machince? If so which ones? Speaking of this - how to I run backups of my configuration in case the monitoring box goes down? Thanks! Wayne
Juniper Router Stats
Is there any way to get Opmanager 5.6 to show interface stats and memory/CPU for juniper Routers? I have added my Junipers as custom devices and loaded the MIBs to the MIB folder. I can see the interfaces but I cannot get any stats to show. Am I missing the boat here or is this somethign that Opmanager cannot do?
SSL on OpManager
Hello, I'm trying to put SSL on my existing OpManager installation. I recompiled the Apache Webserver with the SSL module without to much problems. When SSL is activated in the Apache configuration, OpManager doesn't start up. However, everything works fine with the new compiled Apache when SSL is disabled. Do I have to change the config of OpManager somewhere ? Do you have a kind of HOWTO for SSL on OpManager ? Regards, Sacha
Firewall monitoring
Hi all, I have to firewalls CISCO PIX and S-box (checkpoint safe@office). For some reason i cannot monitor any of them. I provided the username and password for s-box but it's not working, moreover Pix doesn't ask for any username when you connecting to it from ssh/telnet. I configured the snmp community on PIX - and still nothing. Please help....
Real remote monitoring
I want to know if the following is possible. I have 3 custumors, each with a DSL line. I want to monitor the server and servr apllication's. I dont want a VPN connetion to the custumors so on the custumors side i need to install a sort of agent that send data to the monitoring system. Is this possible?
Cannot Uninstall/Reinstall OpManager
I have been using the free version of OpManager. For various reasons I have had to uninstall/reinstall it a couple of times. I have been trying to re-install it after de-installing it, but every time I run the installation, I get a message saying 'do you want to uninstall opmanager?' I say Yes, the process finishes, then I run the installer again to re-install, and get the same message again. I have checked the registry and the file system, and I can't find anything to do with OpManager in either,
Interface Ports
Switch mapper created picture of switch but when I unplug a port it does not see the change.
OPManager Database to externa MYSQL-Cluster
hy everybody, i would like to outhouse my local OPManager-Database to a externa Mysql-Server. How are the procedure to realized it? thanks for help, chris
How to remove OpManager Service
I am trying to install OpManager. I previously was using the free version. I ran the uninstall from the Control Panel. Now when I go to re-install OpManager I get a message saying 'do you want to uninstall opmanager?'. I reply yes, then get a message telling me that the OpManager service is being removed. The process runs to completion. I then try to run the installer again, and get a message asking me if I would like to remove Opmanager. I then get a message saying the service is being removed.
Disk Utilization 100% for Windows 2003 Server
Hi, I have some servers whose OS are Windows 2003 server with more than one SCSI harddisks. However, when I use opmanager to monitor the servers after serveral weeks. The Disk Utilization % always reaches 100%. When I delete the server and add the server again. It is OK again. For another Windows 2000 Servers, they are no problem at all. How can I fix this problem in Windows 2003 Servers? Thx Kevin
Cisco Catalyst 4006-sw problem
This switch is automatically detected as a router and then i can get the details of the CPU and Memory utilization. But When I change the category from router to switch i can get only memory utilization !! ....why is this happening. I tried changing the snmp oid string which the switch used when configured as router but still the TEST MONITOR shows error. PLEASE HELP ME !!!!!
OpManager Reports
When I try to display any of the following reports for Today, Yesterday, or Last 7 Days, I get a "No Data Available" message: * Servers by CPU Utilization * Servers by Memory Utilization * Servers by Disk Utilization * Servers by Rx Traffic * Servers by Tx Traffic * Servers by Rx Utilization * Servers by Servers by Tx Utilization For the most part, the data on the snapshot screens is fine and when I test the SNMP monitors, there is no problem. SNMP is running on the devices. Which MySQL table should
Server Snapshot Monitor icons disappearing
This one is kind of odd. I've been accessing monitors via the web client a lot today and suddently most of my monitors "disappeared". My resource monitor section shows I have no resource monitors, but I know they are there. In fact, the graphs are still being updated. I've attached a screen shot. Any ideas? Walt
struts-tiles
Why this Error is coming, while i am running my server org.apache.struts.tiles.TilesRequestProcessor Tiles definition factory found for request processor ''. I am new to struts.
Next Page