Why Manageengine NetFlow analyzer stops
Hello, I have an evaluation license to test Manageengine NetFlow analyzer , I've installed it on Ubuntu I used this manual https://www.manageengine.com/products/netflow/help/installing-and-starting.html First how to know and check everything is ok ? I
QoS DSCP section show only Default DSCP (000000) and little bit Other
Dear experts, QoS DSCP section show only Default DSCP (000000) and little bit Other I created addition DSCP 2, 4, 8 in Settings, but still only Default In parallel we have another CA Network Flow Analysis app and it show that Top of QoS is CS1 and dscp4
Forwarding flow from Manage Engine OpManager to SIEM
Hi, is it possible to configure forwarding flow (NetFlow, or sflow) which we receiving from network device on Manage Engine OpManager to SIEM tool? Kind regards and thank you for answer.
IN and OUT traffic same
Dear experts, I have two interfaces on monitoring: G0/0/1 Tu1 (source G0/0/1) Tu1 - In-Out Traffic are different values Gi1/0/1 - In-Out Traffic same all time On both interfaces I use commands below: ip flow monitor MONITOR-1 input ip flow monitor MONITOR-1
uninstall netflow
dear all, how to uninstall netflow analyzer 9.5 from a linux machine. regards Bahaa bacharouch
Router Credentials
I just installed Netflow Analyzer to test with one Cisco 2811 router. If I try to add a service policy it says No_Credential in red. I tried adding a credential but it say I already have one for that IP. What do I need to do to set up the credentials for accessing the router properly?
Why Netflow added to monitor ports that wasn't configured to report on Netflow?
Good day, I have switch and router added to Netflow. I configured only one interface on switch to report on Netflow - only this interface appeared on Netflow I also configured only one port to report on Netflow on router. But few additional ports appeared
Error %%4294967295
Hi Support We have updated our server from Server 2008 to Windows 2012 R2, We have the version 9.0 of Netflow analyzer, after do that the service doesn't work, appear the error message %%4294967295, any idea? Regards
NBAR Status is show disabled but can view Layer-7 application
I noticed that the "NBAR Configuration" page on my device displays "Disabled" under NBAR Status, but there is traffic being shown on the Layer-7 application page. Can you help me understand why this is happening and what steps I can take to fix it? Thank
Raw netflow data
Hello to all! Can someone explain, how can I add my raw netflow data to ME Netflow Analyzer?
Error in processing flows for device with ip X.X.X.X as template information is not received from the device
I added a Cisco 2921 router IOS version 15.4(3) to my system, which is able to display layer-4 & 7 traffic. However, I am continuously receiving an error message "Error in processing flows for device with IP X.X.X.X as template information is not received
AI is here. Here's how your ITOps can take advantage of it.
Hello there! The hype around artificial intelligence for IT operations (AIOps) is real. But does your IT need it? This is a question every CIO, CTO, and IT decision-maker needs to address before they choose to go with or against this trend. To help you
Cannot add Mikrotik device in netflow analyzer
Hello team, I hope you doing well. I am trying to add Mikrotik device in netflow analyzer but I cannot do this. I have configured Mikrotik and now looks like to add device I need configure it: I have configured SNMP credential but I am no sure what should
Your invitation to join our LinkedIn Live on AIOps
Hello there! We are conducting a LinkedIn Live session on AIOps (artificial intelligence for IT operations) titled "Mapping the impact of AIOps for CIOs, CTOs, and IT managers." AI is everywhere and the hype around AI in IT operations is as real as it
Cisco ASA SNMPv3
I have a problem with connecting to ASA FW using SNMPv3. Other mgmt system I have does not have a problem with it, so it must be something on NFA. What library do NFA use for it and is there some command line snmp command I could use to test access?
[White paper] AIOps: The journey from reactive to proactive ITOM
Join us as we explore the effective implementation of AIOps in your IT infrastructure, its maturity stages, and potential business impact. We also discuss the past, present, and future of AIOps offerings and the market, along with the current challenges.
Connect with us at ManageEngine North America User Conference!
After a long wait of three years, the ManageEngine User Conference is back in North America, and we are super excited to meet our customers! The conference will take place in May in Chicago and Toronto, and in October in Dallas and Orlando. Chicago User
Is there any limitation on Netflow Analyzer for Evaluation User ?
Is there any limitation on Netflow Analyzer for Evaluation User ? now i only able to generate 2days report.
What is WiFi 6?
WiFi 6 (802.11ax) is the latest standard in WiFi technology, which is an improvement on the previous generation WiFi 5 (802.11ac) standard. It is mainly built to improve the user’s surfing experience by increasing network speed. It improves transmission
Ubuntu can't start netflow analyzer
When trying Starting NetFlow Analyzer Collector (https://info.manageengine.com/products//netflow/distributed-monitoring/help/index.html), I am encountering the error 'Please free the port(s) [8060, 22] before starting the server. I then run 'sudo fuser
Router-switch Christmas sales up to 80% off
Amazing! Router-switch annouced huge disscount up to 80% off to celebrate 2013 Christmas Day.So during the big sale days (from Dec. 13th, 2013 to Jan. 24th, 2014) Cisco buyers can save much more money. It delivered top 50 hot Cisco products, including Cisco 1900, 2900, 3900 routers, Cisco catalyst 2960, 3560 and 3750 switches, catalyst 4500 and 6500 switches, Cisco ASA 5500 and cards, popular Cisco access points and IP Phones, etc. Key Feature of Cisco Switch Catalyst 3560 series Cisco Catalyst
ESP_App shown in flow analyser
Dear all, Is there any way to exclude ESP_app from flow analyser reports? I mean to get full insight in only traffic between real sources and real destinations, because I saw that flow analyser report lists two tunnel IP endpoints as source and destionation
Using Palo Alto FW App IDs
Is the ManageEngine Netflow Analyzer capable of interpreting Palo Alto Networks firewall app ids? I'm evaluating the product and in the PAN I've checked to send PAN field types, but I noticed in the PAN it recognizes a connection on a higher UDP port as stun traffic, but in ManageEngine these connections were identified as an Unknown App. Also, I find that clicking on "Conversation" at times goes nowhere. Even when collection completes it takes quite some time to list conservations for the last
[Webinar invite] How to avoid IP address conflicts in your network
Hello there! Tired of troubleshooting end-user complaints about IP address conflicts? Often, you and your team are only alerted about this issue when an end user reports it or when it cascades into a major network issue. Here's how you can avoid this
SNMP Get OID via API
Hello, I need to perform a task that I would like to automate. This involves querying a device via Settings > Tools > MIB Browser via SNMP. I tried to use the following URL but it returns error code 5002 "The specified URL is incorrect." https://IP_SERVER_NETFLOW:8060/client/api/json/mibbrowser/snmpGet?apiKey=2f6e8b31482f7f9ba882608bcc0fe1be&host=10.10.10.10&port=161&oid=.1.3.6.1.2.1.15.3.1.16&mibname=BGP4-MIB&snmpversion=snmp3&credentialNames=Global
[NetFlow Analyzer Free online training series] Enterprise bandwidth monitoring: Beyond basics
As the number of users in your organization grows, enterprise bandwidth management gets more complex. Learn how you can detangle bandwidth monitoring complexities with NetFlow Analyzer's free online training series. Keeping in mind the convenience of
How can we remove RADIUS settings?
Hello, how is it possible to remove RADIUS server settings from User Managment ? If we try to clear the IP we get the error message "Enter valid server name".
[NetFlow Analyzer Free online training series] Enterprise bandwidth monitoring: Beyond basics
This free online training series will be your guide to eliminate network and bandwidth management troubles while helping you get a better hang of using our integrated bandwidth management solution. Keeping in mind the convenience of IT personnel across
Connect with us at ManageEngine Australia User Conference!
We're thrilled to invite you to our User Conferences in Australia. We'll bring you multiple in-depth product presentations on all aspects of IT management, as well as plenty of tips and tricks, opportunities for one-on-ones with product experts, and some
Where can I download Netflow Analyzer ???
Dear Support, Please can you share the link to download NetF Analyzer. Been searching but seems like I'm searching on the wrong section. Thanks
Supported Operating systems list for Netflow Analyzer installation
Dear Users, Please be informed that from July 31st onwards, NetFlow Analyzer application will not support these operating systems (and the older versions below it) for its installation. Windows 7 Windows 8 Windows Server 2008 CentOS 6 RedHat 6 Mandriva
Uninstall opmanager
Hello, I'm using Manjaro Linux, I installed manageengine netflow analyzer, but now I can't uninstall it. It says in the manual that the folder for uninstalling the software is located at installation folder which is `/opt/ManageEngine/OpManager/_uninst`.
How does RTP get processed?
We have a high amount of unknown application data coming in from sflow. Upon investigation, I've realised it's RTP traffic for a SIP service. Given that RTP can operate on any port, how do we get rid of the large amount of Unknown Application items?
Restoring deleted interfaces
I have several interfaces on a router device that I deleted in netflow. I need to re-add them, and our router should be reporting up to Netflow on them, but they are not dynamically re-adding. Any advice on how to re-add them? Note that our routers are
Getting SNMP IfIndex for already renamed interfaces
Hi, In our Netflow implementation, we have several routers that we recently upgraded to newer models (Cisco). This changed all the IFIndexes, so our previously named (renamed in netflow) interfaces no longer match up with what they are supposed to. Is
NetFlow Analyzer Pitstop - Stopping support for 32 bit installations
Dear Users, Please be informed that 32 bit installations will no longer be available for ManageEngine NetFlow Analyzer. Support will be stopped for all 32 bit installations by September 30, 2022. We request all users with 32 bit builds to migrate to our
Netflow Analyzer Enterprise 12.5 vulnerability to log4j?
Hi, I see that Netflow Analyzer Enterprise 12.5 is using log4j 1.x (which is 6 years End of Life so you might want to think about updating?). According to RedHat this might be suspectible to the same vulnerability as log4j <2.5 if the configuration uses
the web service does not start
Please help me solve the problem with the Netflow Analyser web service. Before restarting the server, everything worked correctly, and after restarting the service does not start. Previously, access was carried out via tcp/8080 port. But today it was
The web service Netflow Analyser is down
Hi, please help me solve the problem with the Netflow Analyzer web service. Previously, access was carried out via tcp/8080 port. But today it was configured to use a tcp/https connection using a self-signed certificate. After these settings, the server
Unable to load web portal
Hi, I recently installed NetFlow Analyzer on Ubuntu 20.04 and the install seemed to work fine. When starting the services it shows them all running, and I can get to the login page at <<IP>>:8060 However, when I log in it redirects me to: http://<<ip>>:8060/apiclient/ember/index.jsp#/
Next Page