Changing snmp precision
We recently purchased some Inrow cooling solutions from APC. Since there was no device template in OpManager i created a new one after downloading the MIBs from APC. When I setup some bulk monitors i noticed that the values output as a 1/10 of a kW or 1/10 deg Cel. This makes the monitor confusing, is there any way to do simple maths on the returned value such as snmp value / 10 to get the actual kW ? thanks Chris
Backup and restore process of OPmanager 8
Hi everyone, I am using OPmanager 8 and i want to take all devices, business maps,notification profiles with alerts rules backup and then restore them on fresh OP manager machine. Kindly help me in this regard. Thanks, Arshad
OP Manager Suddenly not showing Router/Switches interfaces
Hey everyone, I am using OP manager 8 and suddenly it stop to showing routers/switches interfaces.When i rediscovered device interfaces then it showing interfaces but after that it again stop to showing interfaces. Kindly help me in this regard Thanks
Does displaying multiple real time traffic widget on the dashboard 24x7 creates network congestion?
I'm thinking to create a dashboard with multiple real time traffic widget to monitor some of our servers and have the dashboard display on 24x7. Does that create network congestion or slow the devices that I'm monitoring?
Notification profile for multiple, but not single failures?
Is there potentially a way to configure a "run program" notification profile to cover three devices, only triggering if all three are unreachable and not triggering if only one or two are down? My aim is to monitor a server's connection to the internet (the server on which OpManager is installed and which is managed remotely) by monitoring three outside IP addresses, classing it as internet failure when all three are unreachable and not just when one of the outside devices are unreachable... Any
OpManager 8 can't email distribution list?
Hi all, I have OpManager 8 configured to email me when a device I'm monitoring stops responding, and that works perfectly. When I go to the notification profile and tell it to send a test email, the email arrives immediately. I just had our Exchange admin create a distribution list or distribution group so that I can email more than one person when a node goes down, and when I try to email that group from OpManager, the email does not go through, even though it announces that the email was sent
Folder Monitoring on Localhost Not Working
I am starting off of a clean database on version 8723. I add in the "localhost" (Windows XP Type) as one of the devices and try to associate a folder monitor to it. However, no matter how I set up the folder monitor I do not get any information or alarms. Then after playing with it for a while, I start getting an error saying that I need to configure the credentials for the device, but since it is the localhost I cannot. If I delete and re-add the localhost this message goes away, but I am still
Cisco ASA interface graph not showing
I have configured to monitor Cisco ASA firewall with SNMP polling. I can see the cpu, active connection and availability but I cannot see the interface graph. it is currently blank. what do i need to configure to see the interface traffic in Opmanager. SNMP RO string is tested okay.
OpManager failed to start
Dear all, we had an unexpected issue yesterday and OpManager fail to start since this. I would like to attach to this post wrapper.log and startout.log but no way to attach documents (tried with ggle, dsktp, zoho ??). Is there an other way to send u our logs ? Thank you i advance for your support, Christophe Boudeau IT services GEA Group Extract fom wrapper.log : INFO | jvm 1 | 2011/07/26 18:26:40 | at java.lang.Thread.run(Unknown Source) STATUS | wrapper | 2011/07/26 18:26:43 | <--
Particular Alarm Suppressions
Is there any procedure in OpManager to suppress particular alarm rather suppressing all alarms?
A bugs of getting interface traffic
The interface traffic is 0. This bug occurred everyday.
Typo in OpManager (Spelling Error)
It should be 'authorized'
OP manager 8 suddenly stop to showing Router/Switch interfaces
Hi everyone, I am using OP manager 8 and suddenly it stop to showing router/switch interfaces.When i rediscovered interfaces then it showing interfaces but after that it again not showing interfaces. Kindly help me in this regard Thanks
SQL Query for Custom OpManager Report
Dear All, I want to create a custom report for servers from (1) specific Business view, for the (2) last 7 days, from the (3) Last 7 days of the following monitors: - CPU Utilization - Memory Utilization - Response Time Can somebody provide me SQL query to retrieve this information? Thanks, bsnieva
Invalid charasters in WMI classes list
Hi! I have installed OPManager 8.8811, try&buy license. Database located on a server MSSQL. OS Windows 2008 in Russian language When I try to create a WMI-monitor I see following list:
monitor windows XP and windows Vista didn't work
i will monitor windows XP and windows Vista agent, i use wmi to connect. It test credential passed status but when i monitor didn't work, can't reply back cpu, ram and hdd data. (windows 2003&2008 it's work) plesae help
Monitor CPU and Memory on Foundry MLX
Hi, I can not see the monitors CPU and memory on my Foundry MLX-4. When I add them, do not appear on the list. So I created a new monitor but I can not put it on dial-graphs. Could you help me?
Historical reports not working
Hello, We have latest OpManager 8011 running on SQL Server 2008 R2. We recently discovered that historical reports are not working. We had a problem with database running out of space, but OpManager did not complain. The problem with database was recovere one week ago, still not even same day data is being reported. Checking the database tables, we see STATSDATA<date>, ElementAvailabilityDaily and Hourly all full of data. Appreciate help on seeing what is wrong. Thank, Jalal
Possible solution on Oops... ... Run repairDB.bat
Hi there, I´m running OPmanager 8 and all of a sudden it does not work, can´t log in saying Oops .... run RepairDB.bat to... but that doesnt work either. I´m also running McAfee on all our servers and it seems that the McAfee client is doing something with the OPmanager server... I stop the McAfee, close the server, runs RepairDB.bat, starts the server and it is all working again.. I dont know what to do in the McAfee to go around this, but the investigation continues ;) //Magnus
Network Configuration Management
Hello I have installed the NCM Plugin (trial version) in my Opmanager 8. (build 8811). Installation was OK. I get the "Network Configuration Management" tab on top of OpManager, but when I click it I only get a page saying "[!] Sorry, the page you requested was not found" Any help will be appreciate. Thanks in advance
Opmanager for mobile browsers?
Hi, will there ever be a release of a mobile version of Opmanager? I would like to be able to view my network status fom my Blackberry. Thanks!
Add Bulk
Hi Gabriel, I successfully added monitor on "Add Bulk' and responded on the test. But we encountering problem on the alarm, the threshold that we set on this monitor is already riched but there is no alarm. Please see my attached file. Thanks, Joe Reyes Pre-Sales System Engineer AG Datacom Phils., Inc
Traceroute from OpManager
Hello, How do I enable traceroute service on OpManager? When I try the traceroute from the GUI, it asks me to specify the traceroute service path in /conf/Ping.Properties file. I have already done that as below, but it still gives me the same message. tracePath=/bin/traceroute Do I need to restart OpManager service after this change?
Report
Dear Team I need to know the list of reports which can be generated out of the box for each module. We can find what can be monitored on most of the module but what reports can be generated is not available unless you install and check yourself. So it is better if a document with report formats are available as well on the net as pre-sales activity Bhupesh ASPGulf
Some stray entries found for this device
new server add and this error "Some stray entries found for this device"
Shortcuts in Business View will not show unmanaged status
We have created a map in business view that will show an up (green) or down (red) status but will not display gray for Un Manage. The Device itself shows as it should. Was this a known problem for build 8721?
unable to get all mount drive in Linux OS
Hi all, Please I need you help I have a problem that it the OPmanager unable to get all mount drive in Linux OS using CLI dose anybody have a solution BR, AA
TOP 10 CPU Utilization, Hard disk utilization and Memory Utilization does not appear
HI, I am using 8811 OpsManager. I have 9 domain controllers and one router being monitored. When i look at dashboard , overview,,, i cannot see the any statistics in TOP 10 widgets (memory, cpu). I tried changing setting from top to all devices but nothing showed. When i go to MAPS->DOMAIN CONTROLLERS-> LIST VIEW, then i can see on rights side the utilization statistics bar.Attached is screen shot. Any idea abou this issue? Regards, Abbas
Monitoring OSPF
HI it is possible to monitor the ospf link states in opmanager build 8721. If your answer is yes, you can tell me how?. thanks.
Notifications Not Working
OpManager Build Number: 8810 Hi, I have configured all my Servers, Routers and Switches with a notification profile. At first I used the email notification by setting it up accordingly. If I test the notification it works and I receive the test mail. However, I have several experienced incidents where OpManager does not send an email notification to me when any one device goes down. (I only notify for Critical Alerts and if the device/interface misses 1 poll). I immediately test again in order to
Problem with configouring WAN RTT on cisco 3825 router
Hi, when i try to configure WAN RTT MONITOR on CIsco router i get this error \ Can anyone help mi with configuration of Cisco to support this feature? This error is probably related to change config on Cisco via SNMP.but i can`t understand why.. My IOS on router supports IP SLA but no "ip sla monitor..." command is available.
Trigger Alarm based on time/weekday
Is it possible to trigger an alarm for a (group) server(s) on a scheduled time/date. We want tot trigger an attention alarm for a group of server on monday. Then another group of servers on the next day etc. Is this possible with opmanager, or do I need to use a workarround? Create events, batchfile etc? Regards Ralph
problem with sms alerter.
Hi, Sinds a few days, I didn't receive my sms notifications. Last week, I have created a bad sms profile (with a wrong mobile number). Is it possible that my problem is caused by a queue to the wrong number? Regards, PYM
Remove custom WMI monitors
Simple quesiton, how can I delete completely custom WMI monitors I added in OpManager (build 8720)?. I am only able to remove them from the devices but can't figure out how to remove them from the monitors list under WMI section. Thanks
VER - Switch port mapper slow and sometime doesn't work
Hi, I just installed the OPM 8811. I tried to use the "Switch Port Mapper" feature on several switches. The customer and I found this feature slow and unpredictable. Some time I have no data, some time it takes minutes to have a simply mac address table, some time I have an error message and sometime nothing. This is the same behavior I am facing with other customers and with several OPM releases. The customer claim that with Solarwinds this feature is really fast and reliable. One thing we also
Schedule report folder
Hi. Can I change the folder where the scheduled reports are saved? I want to save the reports at another server. Thanks. Antonio.
How can I get a simple report showing which alerts are assigned to which devices?
I need to get, for purposes of review, a list or Excel spread sheet showing the device, it's category and which alerts are set on it. We need to review with a group of people and something to use like that would be very helpful.
APC UPS report
Hi. I'm monitoring 8 APC UPS and I created a Business View to agregate all of them. At the List View of this BV, I can only see CPU and Memory %, but I want to see the UPS load listed. If this view cannot be changed, is that any way to create a custom report to show all UPS load and charges at the same report? Thanks. Antonio.
TCP/IP Checksum Error/Packet Loss Checks?
Dear All, In OpManager product, can you check TCP/IP Checksum Error or Packet Loss? Thank you in advance.
Delayed Email Alerts
Hi, I am just evaluating OpManager and I have setup a few email alerts for various devices but I have realized that I only get the email exactly 1 hour after the alarm was raised. For example, at 1pm yesterday a server went offline while I was working on OpManager and I seen the alert but I only received the email notification at 2pm. When I send a test alert, or even if I send a report via email from OpManager to the same email address, I receive it within 10 seconds. I dont have any email monitoring
Next Page