Serverscheck integration
Hi. I integrate the Serverscheck to OPManager and I want to monitor the temperature in the room. I also want it to alert me when the temperature is high or critical. But the conditions are (Not Contains, Contains, Not Equal, Equal, Match Regex). Please see attached photo.
NCM - backup config SHDpassword password change
Hello! I have updated opm to 12 version and i'm tryng to backup router config whit NCM plugin. Backup is ok, i want to save: @EX4300# show | display set | save scp://deviceexpert@192.168.12.14/302_ConfigFile.txt Entering into Network ConfigManager SSHDpassword Enter password for deviceexpert Password: 192,168.12.14 is opmanager machine where i can change the deviceexpert password ????? In general setting of NCM i see this but the password? thanks!
SNMP trap FLOOD
Hi Opman guru's, For Opmanager TRAPS, We need to be notified for every received SNMP Trap, EXCEPT, when there’s a major failure and there’s a flood of sent SNMP Traps – in such situation, we want ‘policing’ type of throttling. For example, if rate of sent SNMP Traps exceeds 5 within a period of say 1 minute, then I don’t want to be notified any more until the rate decreases. This is mainly an issue with E-Mail to SMS as we are getting floded is it possible to tume this. Thanks, Stephen
Create Trap processor
Hello in free version of opmanager 12.2 there is a limitation on new trap ? (i'm waiting the conversion of license file from the vendor) I'm trying to add new trap from mib and from create trap proccessor but does not work. if a try to add from mib once added if i try to enable does not work. If i create a Trap preppocessor des not save Match Criteria and Rearm Criteria , and when i save the new trap i'm not able to enable it. Regards Franco
VIwebservice not get any data from vcenter
Hello Guy, I have a problem monitoring with OPmanager . Opmanager VIwebservice protocol is not get any data from vcenter and not enbled in threadhold.I was suspected for below print screen which was occurring in OPmanager. Guy, could you give the perfect solution and suggestion about this case?. I hope that you will give me best solution for me because I'm just a newbie in OPmanager Our OPmanager build number is 12000 Thank
IBM SVC 3700 snmp fail -OPMANAGER 12.2
Hi, Iam using OPManager build 12.2. I tried to add IBM SVC3700 thorugh SNMP, but snmp failing.Tried both V1/V2 & snmp V3 but same result. Is there any option to add IBM SVC3700 storage in OPM.
OpManager 12.2 session timeout not working
Hi, I have OpManager 12.2 Central Server & Probes installed on our network and I'm attempting to set a session timeout, so the user is logged out after 10 minutes of inactivity. I achieved this in ServiceDesk Plus by editing the session-timeout attribute in 'ServiceDesk\server\default\conf\web.xml'. However a similar approach does not work for OpManager. The auto-refresh interval has also been disabled but this hasn't helped. How do I set a session timeout for all users in OpManager? Thanks
Run a perl script under windows
Hello, I have a perl script I have removed from a nagios system. I have installed Perl on the Opmanager server and can successfully run the script from CMD on the opmanager server and get the output im expecting. I now want to be able to have opmanager monitor this script and generate an alarm based on the output. My issue is for the life of me I cant get the script to run. The commands I issue in the CMD line are "perl check_cvprocessing.pl cvprocessing 60 180" How do I get this to run in opmanager?
User and Password OpManager OVA Demo,
Download the OpManager OVA but I do not have user information and password to access the DEMO virtual server. Can you help me with this information? Thank you
NCM Credentials
Hi there Pls where can I find the TELNET/NCM credentials, to modify or delete them? Thanks Regards
How to get the vendors list that OpManager can manage and operate
Dears, I want to know which telecom. and IT vendors that OpManager can maintain? Main target is for Wifi AP, switches, routers and so on. Thanks!
Opmanager 12 licensing question
Just a couple of questions with regards to licensing between v11600 and v12.2 1. How would licensing work for upgrading from v11600 to v12.2 as we are currently licensed for only 100 devices with no plugins but 12.2 Enterprise Edition allows more devices than 100 devices and now has the plugins as standard? 2. We have been evaluating 12.2 Enterprise Edition and have it almost configured the same as (if not better than) our 11600 setup but with nearly 200 devices. Is it possible to transfer the licensing
VLAN Interface details Problem
Hi there When I open the details of a switch device and click in one VLAN, OPM open the VLAN Details but I can't close the page or back, and if I refresh the page I see empty page. I have to delete the string of my URL after the root address and refresh or close and open the tab Regards
OpManger does not start
Hi Guys, I have installed OpManager 12. While I can not use port 80, instead I used port808. The Installation succeed without any issues. However, Opmanager stays on "Initializing" screen. Any Help to correct this issues is appreciated. Thank you Nilanga
Opmanager 12.200 APM Plugin Integration
Hi I have OPM 12.200 I downloaded APM plugin and installed it on the same server. Trying to access http://serverip:9090 gives me information that I need to acces via OPM (the plugins works) But I can not find any tab in OPM regarding APM. Where can I find tab in OPM to configure APM In admin Add-On/Product \Integration under Application Manager I have server detail filled I am asking because my license for OPM and APM is just one file
VMManager Plus - VCSA 6.5
We just installed the VMWare vCenter Appliance (VCSA) 6.5. I'm looking at some ManageEngine tools and one of them is VMManager Plus. I cannot add the VCSA 6.5 appliance to VMManager Plus. I get a "Add Device Failed" error message. I've tried Windows Crendentials, VMWare credentials, etc. and I can't VMManager Plus to add the VCSA appliance to VMManager. Has anyone else came across this problem? Jesse
Monitoring View Cloumns and saving the filters
Hi There It would be great add a new option to active o deactivate new columns in the Monitoring View to add for example Device notes or devices dependencies fields, sort the view with these fileds. Everytime when you apply a filter by categories and open a device details or change view if you back in the monitoring view you have to apply the filter again! frustrating same problem with filter of the page (selected to see 500 devices but back to 100) Add an option to apply and save the filter status?
WLC Aruba Conf
Hi There I have 2 Aruba WLC 7210 I have add in OPM but I can't understand how can configure the end user tab. Somebody can support me?
Trap processor issue
Hello, I configured a trap processor for a getaway and I can see the this: Message: test5 trap received from xxxxx with SNMP Varbinds sysUpTime.0: 17 days, 1 hours, 44 minutes, 58 seconds. , snmpTrapOID.0: .1.3.6.1.4.1.5003.9.10.1.21.2.0.49 , .1.3.6.1.4.1.5003.9.10.1.21.1.1.0: 48 , .1.3.6.1.4.1.5003.9.10.1.21.1.2.0: Alarm cleared: Trunk LOS Alarm. , .1.3.6.1.4.1.5003.9.10.1.21.1.3.0: Interface#0/trunk#2 , .1.3.6.1.4.1.5003.9.10.1.21.1.4.0: 0 , .1.3.6.1.4.1.5003.9.10.1.21.1.5.0: 315 , .1.3.6.1.4.1.5003.9.10.1.21.1.6.0:
need help with esxi 6
try to monitor vcenter that including mix of 5.0 & 6.0 esxi version after scanning i can see the hosts but cannot monitor the 6.0 version im using the last version opmanager 12.2 any ideas ? thanks
Best category to match Bluecoat Proxy SG?
Hi Please someone advise what is the best category to match Bluecoat Proxy SG? Thanks, Ramesh
OpManager 12.2 service pack released!
Hi, We are glad to announce the release of the much awaited OpManager 12.2 service pack. This is one of the biggest service pack release in the history of OpManager and hence the delay. However, we thank all our customers for waiting paitently for the release of this service pack. What 12.2 has to offer for customers using OpManager 11.6 (or lower versions)? Unified network management: OpManager 12.2 allows customers to upgrade to a unified network management software that includes various network
IF Alias in IPAM published data
Good morning, When i look at the IPAM results i see the IF Alias showing the names of the ports on the switch, however when i select to publish the data it is not a column for me to choose, i am building a map to give a view of hotdesk usage and require the Alias to be published along with the Data, is there a means to do this? I've tried using the data from SPM+, however as it does not have an add-in for currently logged on user the data is viable for my needs Many thanks EDIT As an additional the
exclude drive/volume from space checks
we are all of our page file drives setup at the "P" drive and they all show up as "Volumes with the most usage".. Is there a way to exclude all "P" drives? Thanks in advance Mike
Opmanager shows more VMs on dashboard than in Inventory
Please explain why OpManager (build 11500) shows more VMs (Number of VMs on summary dashboard ) than in Inventory Details:Summary shows 9 VMs on host (fig1.jpg), but inventory only 7 VMs (fig2.jpg). Figures is attached. Regards
OpManager12 Webinar 22nd November 2016 - Question/Answers!
Hello Everyone, Thank you very much for the overwhelming response in our OpManager12 Webinar session(video). It was a great experience over all. There was no surprise that we had many questions during the Question/Answer session and unfortunately we weren't able to answer all of them due to insufficient time. Herewith attached the compilation of all the questions with answers for the benefit of the wider audience. Please check and comment below for any more questions. Cheers, Suresh Bagavathy OpManager
IE Compatibility?
Hi There With IE 11.0.9600 I can' see the table for DB Query and other support tools
Regarding categories question
Hi all, Please be infomred that I created a category call "file server" which include 10 servers and other category call "FTP" include 5 servers. May i know can i create a category call "infa" then include above 2 categories then monitor all servers (total 15 servers.)? thx
Multi Delete Devices Server Crash
Hi there This is the third time, I'm just testing the OP12.2, I have add devices and when I delete these devices with multi select the warpper service crash and restart. I think it is need to check these issue Regards Ivan
Opmanager 12 - ssl?
I've installed an opmanager 12.1 installation, to look at the changes, while we wait for migration update for 11600. The documentation for opmanager 12 (link) points to old install documentation, which is no longer relevant. I need to SSL this to securre the active directly authentication option.. where is that document?
Can't restore database on new installation OpManager 10000
Hi, I did fresh installation OpManager 10000 on Linux machine and try to restore MYSQL database from backup made by same OpManager build (same Linux). But restoration not successfully completed. In restorelog0.txt I have: [11-22-2016]|[15:14:31:553]|[FINE] : ************** Restore operation started ********************** [11-22-2016]|[15:14:31:553]|[FINE] : Restore started on 11-22-2016 at 15:14:31:553 [11-22-2016]|[15:14:31:554]|[INFO] : Extracting property file please wait .....
Setting up SNMP OPManager v12
I want to setup SNMP credential but I'm confused as to how to do it. Not sure what to put on the places I mark below.
Windows AD security with nested groups
Hi, We have group hierarchy like the following: - adm user account - member of general admin group - this group is member of OP manager admin group. this is so we have roles / function groups within the AD. is this a workable solution ? kind regards Bauke
OpManager license
Hello i would like to know if license of opmanager 11.6 is compatible with opmanager 12.2 Regards Franco
Upgrade assistance
I have downloaded the latest version of OpManager. I cant figure out as how to upgrade from earlier version of 12. when I run setup, it says I must un-install older version. I don't want to lose any configuration, please let me know the steps to upgrade to latest 12.2. from earlier version of 12. thanks
IPAM & SPM Add-On for OpManager trial license
Hi, I'm new administrator in this office and newbie with OpManager standard 11.6/ I would be interested in IPAM & SPM evaluation since it just expires after activated yesterday Any other new way to get the new eval key for the purpose of assessment?
Opmanager monitor "Units" is in percentage even after changing to "GB"
I want to monitor my disk space in GB instead of percentage % because different disk has different sizes and percentage is not the best way to monitor disk space for 100s of servers. I tried to change monitor units to GB but it still gives me % value, see screenshot attached. any help to rectify this issue. Thanks
OPM 12.100 can not use Domain Credentials - domain allready exist
I have set up windows auth. It is allready working. I have added one operator. Now I want to add additional users and I can`t It seems that OPM can not see earlier entered and configured domain
Interfaces Up and Down notification
Hi There Opmanager 12.2 I have about 100 switches listed in my opmanager, If I don't want to receive notification when some interfaces going up and down I have to unflag the status PO option? but I have to click in the interface one by one??? No multi select option?? (it was there in the OP 11) For examble I have clients switches and I receive the notification every day when the users shutdown and turn on the computer, because the interface go up and down, but I want to receive this notification
OpManager 12.2 upgrade issue
While upgrading from 12.1 to 12.2 I am getting error All services for OpManager are shutdown wrapper and java not running in task manager
Next Page