Help needed with adjusting/modifying graphs
Hi all,
I run into a problem which is quite annoying to me.. :(
We've some AKCP Environmental SensorProbes hanging around.
We've the 2-ports and a 8-port version of these devices, but not all of these devices are fully equiped with sensors in both or all ports.
In 3 of the 2-ports devices we've all ports occupied with a sensor that measures both temperature and humidity. In the 8-ports device we've in port 1-4 watersensors and in port 5/6 Temp/hum.
OK.. I've managed to tell OpManager where to get the MIB from, sofar so good.
But then the problems begin to rise. If the device is not fully equiped I don't want to monitor the ports that aren't in use, I only want to monitor the ports in use by temperature and humidity sensors. Furthermore I want the values retrieved by SNMP to be graphed in separate graphs within OpManager.
And then I run into problems.
Is there a nice, convenient and simple way to tell OpManager that it should only read out the values of specific ports (the Temp/hum ones), ignore the remaining ports and, just as important as the whole thing above, graph the specific ports separately from eachother.
When I tried to adjust opmanager_graphInfo.xml to tell it that I want to use multiplenode it was the reason for OpManager Apache service to crash continiously. I put all changes back to the previous state and it went all fine again.
What should I do to tell OpManager that I want separate graphs from variable OID's, how can I delete readings from an unused port in the graphs?
To make any help a little easier I provide you below with the SNMP OID's I want/need to monitor. Thanks in advance for the help!
Regards,
Minollie
---
Temperature Values in C:
.1.3.6.1.4.1.3854.1.2.2.1.16.1.3.0 # Port 1
.1.3.6.1.4.1.3854.1.2.2.1.16.1.3.1 # Port 2
.1.3.6.1.4.1.3854.1.2.2.1.16.1.3.4 # Port 5
.1.3.6.1.4.1.3854.1.2.2.1.16.1.3.5 # Port 6
Temperature Status, down/up/normal etc:
.1.3.6.1.4.1.3854.1.2.2.1.16.1.4.0 # Port 1
.1.3.6.1.4.1.3854.1.2.2.1.16.1.4.1 # Port 2
.1.3.6.1.4.1.3854.1.2.2.1.16.1.4.4 # Port 5
.1.3.6.1.4.1.3854.1.2.2.1.16.1.4.5 # Port 6
Humidity Values in %:
.1.3.6.1.4.1.3854.1.2.2.1.17.1.3.0 # Port 1
.1.3.6.1.4.1.3854.1.2.2.1.17.1.3.1 # Port 2
.1.3.6.1.4.1.3854.1.2.2.1.17.1.3.4 # Port 5
.1.3.6.1.4.1.3854.1.2.2.1.17.1.3.5 # Port 6
Humidity Status, down/up/normal etc:
.1.3.6.1.4.1.3854.1.2.2.1.17.1.4.0 # Port 1
.1.3.6.1.4.1.3854.1.2.2.1.17.1.4.1 # Port 2
.1.3.6.1.4.1.3854.1.2.2.1.17.1.4.4 # Port 5
.1.3.6.1.4.1.3854.1.2.2.1.17.1.4.5 # Port 6
I run into a problem which is quite annoying to me.. :(
We've some AKCP Environmental SensorProbes hanging around.
We've the 2-ports and a 8-port version of these devices, but not all of these devices are fully equiped with sensors in both or all ports.
In 3 of the 2-ports devices we've all ports occupied with a sensor that measures both temperature and humidity. In the 8-ports device we've in port 1-4 watersensors and in port 5/6 Temp/hum.
OK.. I've managed to tell OpManager where to get the MIB from, sofar so good.
But then the problems begin to rise. If the device is not fully equiped I don't want to monitor the ports that aren't in use, I only want to monitor the ports in use by temperature and humidity sensors. Furthermore I want the values retrieved by SNMP to be graphed in separate graphs within OpManager.
And then I run into problems.
Is there a nice, convenient and simple way to tell OpManager that it should only read out the values of specific ports (the Temp/hum ones), ignore the remaining ports and, just as important as the whole thing above, graph the specific ports separately from eachother.
When I tried to adjust opmanager_graphInfo.xml to tell it that I want to use multiplenode it was the reason for OpManager Apache service to crash continiously. I put all changes back to the previous state and it went all fine again.
What should I do to tell OpManager that I want separate graphs from variable OID's, how can I delete readings from an unused port in the graphs?
To make any help a little easier I provide you below with the SNMP OID's I want/need to monitor. Thanks in advance for the help!
Regards,
Minollie
---
Temperature Values in C:
.1.3.6.1.4.1.3854.1.2.2.1.16.1.3.0 # Port 1
.1.3.6.1.4.1.3854.1.2.2.1.16.1.3.1 # Port 2
.1.3.6.1.4.1.3854.1.2.2.1.16.1.3.4 # Port 5
.1.3.6.1.4.1.3854.1.2.2.1.16.1.3.5 # Port 6
Temperature Status, down/up/normal etc:
.1.3.6.1.4.1.3854.1.2.2.1.16.1.4.0 # Port 1
.1.3.6.1.4.1.3854.1.2.2.1.16.1.4.1 # Port 2
.1.3.6.1.4.1.3854.1.2.2.1.16.1.4.4 # Port 5
.1.3.6.1.4.1.3854.1.2.2.1.16.1.4.5 # Port 6
Humidity Values in %:
.1.3.6.1.4.1.3854.1.2.2.1.17.1.3.0 # Port 1
.1.3.6.1.4.1.3854.1.2.2.1.17.1.3.1 # Port 2
.1.3.6.1.4.1.3854.1.2.2.1.17.1.3.4 # Port 5
.1.3.6.1.4.1.3854.1.2.2.1.17.1.3.5 # Port 6
Humidity Status, down/up/normal etc:
.1.3.6.1.4.1.3854.1.2.2.1.17.1.4.0 # Port 1
.1.3.6.1.4.1.3854.1.2.2.1.17.1.4.1 # Port 2
.1.3.6.1.4.1.3854.1.2.2.1.17.1.4.4 # Port 5
.1.3.6.1.4.1.3854.1.2.2.1.17.1.4.5 # Port 6