Huawei Optix RTN 980
HI I am trying to monitor Huawei Optix RTN 980 using OID's. I have performed a MIB walk but now need to relate the OID to a slot/port and a description, any ideas? thanks
netflow on fortigate WAN interface
hi, i have enabled sflow on WAN interface of Fortigate 90D firmware 5.4.3. configuration as below: config system interface edit "wan1" set vdom "root" set mode pppoe set allowaccess https snmp fgfm set vlanforward enable set type physical set sflow-sampler enable set sample-rate 100 set polling-interval 30 set sample-direction rx config system sflow set collector-ip 10.1.1.139 set collector-port 9996 i can see NFA
NetFlow Analyzer v12 tuning steps
NetFlow Analyzer is an resource intensive product and it need to get to be tuned for best performance for application based on the available system resource.. The NetFlow Analyzer product is more resource intensive application and it comes with default tuning for 2 GB. If you have installed the product on a dedicated machine with plenty of RAM and CPU, you can tune the product additionally to get better performance. You can refer the flow rate based system requirement for NetFlow Analyzer by clicking here
More informations in the applications details page
When we access the applications details page, we are not able to see much information, just the 'Applications Traffic' and "Interfaces traffic for application" Will be so much better if we can have more information on this page like the 'conversations' using this application. -- Tainã Rodrigues ACSoftware Brasil
A good way to get an inventory report?
Hi, I'm struggling to find a good way to generate an inventory report of all devices in NFA. Compared to Opmanager or NCM there are pre-built inventory reports that are very good and informative. In NFA 12.2 there doesn't seem to even be a report for this information. Is it possible to generate this with a DB Query?
BGP AS collect issue
as the picture show , AS4319 was highlighted . but it actully was 135391, if you use as-notation format to express , it should be 2:4319,as i know , BGP AS has extended from 2 Byte to 4 Byte, it looks like NTA did not recognize the pre 2 Byte of BGP AS i test it on analyzer v9 and v12 , it has the same result .
Active Directory Integration
We have just upgrade our installation of NetFLow Analyzer to 12.2 (from 10.250) and would like to make use of Active Directory to authenticate the staff who use NFA. However, when I go to the user management page there is no Active Directory option available. IS there some setting we need to enable to make this available? Thanks Stuart Kett
Others in Conversation shows high Traffic
I am seeing a major chunk of the traffic categorized as Others under the conversation. May I know why I am not seeing the actual IPs of source and destination?
Port of connection mismatch
Hello, I met a issue that port number is mismatch from generate netflow packet. Please refer below: You can see that src is 192.168.200.1:80 connect to dst 8.8.8.14:80 but this is wrong information. In fact, this connection is 192.168.200.1:6453 connect to dst 8.8.8.14:80. Can tell me how do I correct it? Thank you.
Cisco ISR4351 configuration
Hi , I have a customer that needs to monitor flow for his Cisco ISR4351 . if NFA supports that device family . and if yes , please send me the configuration details for that device to send Netflow traffic to NFA Best regards
Webinar: Why do you need Deep Packet Inspection for bandwidth management.
Hello everyone, Deep packet inspection capabilities rely on packet-level analysis to determine whether the network or the application is at fault and react quickly to the issues before it impacts the end users. In order to maintain a proper balance between user experience and bandwidth management, deep packet inspection is introduced in NetFlow Analyzer. It helps to simplify the task of identifying the exact root cause of faults and to keep control on bandwidth usage. Please join us for the webinar
Inaccurate link useage showing in Netflow Analyzer
Hello All, I am not very well versed in Netflow Analyzer but managed to get our key Nexus switch interfaces sending data to our server. Unfortunately the size of the traffic looks way to small. For instance, a WAN link is showing a peak of only 19.65 kbps. I know this is not accurate. I'm wondering if there is a setting change I need to make in Netflow Analyzer or if I need to make a change to the way netflow is setup on the switches. Any help is appreciated. Thanks. Jim L.
reverse DNS in traffic summary
Hi, After the upgrade to the latest Opmanager and Netflow version, there is no reverse DNS resolution in the Traffic summary tab. Is there any way to turn it on?
Java Tuning - Build Number12200
Hi, How do I tune my Java for Build Number 12200. I am getting the attached error occasionally. Thanks
Protocol Mappings
Hi, How can I identify the destination/source ports so that I can map them on NFA? See attached sample. Thanks
NetFlow Analyzer shows only last 24-hr data
I just installed NetFlow Analyzer Free Edition a few days ago. I notice that the charts show the data ONLY for last 24-hrs, even if I select longer time period, like last 7-days, 30-days or Custom. I am on build 12200 and was told to apply the latest fixes and I did. Issue still remains that I cannot see data older than 24-hours. Any help will be appreciated.
Upgrade from v11 to v12
Hi, I can't find any documentation for thee upgrade from v11 to v12, or where to get the upgrade. I see the current Eval download is for v12, but cannot find the download for existing customers. Could someone help please?
Netflow on Cisco ASR 9K
Hi all, I'm using netflow manage engine 9.8.7 and Cisco ASR 9K. This is my configuration flow exporter-map FLOW_EXPORT1 version v9 options interface-table timeout 60 template data timeout 60 ! transport udp 9996 source Loopback0 destination 1.1.1.1 ! ! flow monitor-map FLOW_MAP record ipv4 exporter FLOW_EXPORT1 cache timeout active 60 cache timeout inactive 15 ! sampler-map FLOW_SAMPLER random 1 out-of 65535 ! interface GigabitEthernet0/0/0/0.121212 service-policy input 100M service-policy
Startup question\help
Hello , I want to be able to see which websites my users enter where can I see it? I want to able to see www.facebook www.ebay.com www.youtube.com etc... I have everything working and config but I can only see top source this " 77.125.115.60 97% 73.6 MB 60.56.185.170.interhost.co.il 1% 658.01 KB edge-star-shv-01-lhr3.facebook.com 0% 251.59 KB 212.199.202.34.static.012.net.il 0% 91.39 KB map2.hwcdn.net 0% 77.56 KB ns-med1-vip.012.net.il 0% 61.25 KB 36.47.2da9.ip4.static.sl-reverse.com 0% 58.68
Netflow Last Hour Time View
Hi, We have Netflow into the Opmanager, when we try to display trafic from the last hour, the time displayed is wrong. How can I change this? Thank you for your help!!!
Netflow analyzer 9 enable geo location
HI team i installed Netflow analyzer 9 in my D:\Program Files (x86)\ManageEngine\Netflow, as follow, and put the countrycode in this folder , but i am still getting this error . did i put it in the correct folder ?
How to get breakdown of HTTP Traffic?
In our setup, we see 75% traffic is going under HTTP. How do we get the breakdown of sites within this HTTP traffic?
Traffic widget is summarizing data
Hello everyone I need your help to create a view that shows the traffic in and out of a monitored interface. I have generated it through the widgets but it does not show me the real data (apparently this is summarizing the data since the traffic of output is Less than input). I made a separation in the widget (clicking one of the values of input and output) and this would work for me but when it refreshes, put it back all the data out or in. The NFA version is 12200 is mounted in win 2008 r2 I attached
IP group report IEC or metric units
Hi, We were wondering what for ex. KB stands for in an IP group traffic report. Do you calculate KB as 1000bytes or 1024 bytes (Kibibyte) ? Thanks
can Netflow analyzer show ip address belong to which BGP AS
HI team we have requirement to analyzer where our bandwidth heading to , it is better to show out which BGP AS ip address belong to , and what agency own this AS. can netflow import a IP address and BGP database like that ?
opmanager - nbar2 unclassified
Hi, I have created post regarding unclassified nbar2 in the Flow Analysis dashboard of Opmanager. https://forums.manageengine.com/topic/cisco-nbar2-unclassified Do you have any idea what could be behind that, please ? regards Michal
Netflow is not populating, corresponding error in Stderr
Trying to get netflow working for some devices, we know that netflow is being recieved by Opmanager, but the Netflow page for the flows never poplates. If you look at the interface, it shows as purple and shows snmp uknown, despite the device SNMP credentials being correct and verified. This started happening around the same time OpManager started throwing an error in its stderr logs: :921]|[03-22-2017]|[SYSERR]|[INFO]|[399]: java.lang.NullPointerException| [10:38:37:921]|[03-22-2017]|[SYSERR]|[INFO]|[399]:
How long does it take usually to get a response?
When we report a problem in the forum for free tools, how long does it usually take to get a response?
Unable to get traffic details
NFA is receiving flows and even reporting source / destination IP addresses, but all traffic numbers are showing as 0.00 Is there something in the config I need to tweak? Thanks!
Daily average vs hourly average
Why when I want to generate traffic monthly report get different average,for example January the graph is plot based on hourly average while February calculated by weekly average?
Please delete this post
Please delete this post
Network Analyzer Report
Anyone can explain to me what is Qos ? and why the default is using high bandwidth ? Thank You.
Access Level Management: Can i restrict "Operator" to view certain page such as Alert Profiles, Application/ QOS maps / User managed, etc
Greeting, As title. I browse through the forum and couldn't find anything about this. Anyone can guide me how to update manage Access Level? For example, i would like restrict "Operator" to view certain page such as Alert Profiles, Application/ QOS maps / User managed, etc Thank you.
Show "output" as OTHERS in conversation
I set the Cisco ASA 5508 to export to Netflow but I can only see information regarding the IN traffic. Can someone help me? I'm using Netflow Manage Engine 10.2.5 with mysql
Enable net flow export will it affect router performance ?
Enable net flow export will it affect router performance ?
Some Questions about NFA
Hi All, Recently we have a POC about NFA for customer who has OPM v11600 version to monitor network devices. Here is the detail info: NFA version is v12100, source data are from Cisco/Huawei. All flow version uses v9 including Netflow and Netstream according to userguide. Question 1: Respectively from NFA and OPM, the same interface in/out value is deffierent as attachement. As we known, OPM mainly get the data from SNMP protocol and NFA get the
New Interface Type - NFA
Hello, Pretty new to NFA, but I'd like to add a couple new Interface types. How is this done? I'm running a Linux install of NFA. Thanks in advance!!
Version 12 Distributed NFA Availability
When will the distributed version 12 of NFA be released? We have been waiting on it for several months. Thanks, Doug
NetFlow plugin upgrade
I am upgrading my OpManager and NetFlow Analyzer and I have an issue. My OpManager was 9200 and NetFlow was 9000. I updated the OpManager to 9410 and at the end of the process it said to upgrade NetFlow BEFORE starting OpManager. However, when I tried to update the NetFlow using the 9000 to 9700 ppm file it says that is not compatible with what I have. I've downloaded all the files for each to get me current but I am stuck on my second step. Any help would be appreciated, sooner the better. Thanks
Need help: if the Cisco devices is not supported
Hello, i'm plan to setup the network analyzer at my environment but being noticed that the model of cisco devices is not supported, may I know is that any way I can do ? appreciate your advice as I really need the apps to monitor our network right now. Thank You.
Next Page